Question about iflo Home

Open Question

Mixer shower not getting hot - iflo Home

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
blueextc3221
  • 15935 Answers

SOURCE: shower mixer taps

look for a scald safety screw adjustment. Remove the handle, and it is underneath. this is for safety of young children, and is factory set.

Posted on Dec 23, 2008

Ad
gary1121
  • 332 Answers

SOURCE: no hot water to shower since new rad was added

take the shower head off and make sureits not clogged,, if it's not then valve has dirt in it you need to take the cartdrige out or the stem depending on the diverter and clean it out, but it does appear to be dirt, maybe solder got into the water line and came up there

Posted on Jun 06, 2009

  • 349 Answers

SOURCE: adjusting the scauld guard on a shower mixer valve

Uue a 1/8" allen wrench to remove handle to access the dial that set's the mixture of water.Remember or mark where it is and remove and reinsert counter clockwise about a 1/4 turn to start to you reach desired temperature setting. Be careful not to set it at a hot enough setting to burn you.
Once dial in place slide handle on and turn on to check water temperature.

Posted on Aug 01, 2010

ToecutterPA
  • 13 Answers

SOURCE: water not warm enough comming from shower. Very

Replace your Tempering valve cartridge.
Should do the trick.

This will cost a couple bucks for that cartridge.

Posted on Dec 23, 2010

  • 12 Answers

SOURCE: my new triton mixer shower only runs cold water

you might need to adjust the scolding setting behind the handle....

Posted on Jan 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Hot water does not get hot enough, is there a way to adjust the mixer


Yes, it could just be that the intervals of the mixer are getting stuck. This video may help

Sep 16, 2015 | Home

1 Answer

Our bath taps which are a mixer with shower attachment stay really hot if you put the hot on first or really cold if you put the cold on first any idea how to adjust so we can have warm water when turning...


you make no sense. From the picture the water "mixer" is the center lever or is it a diverter valve for the shower and water nozzle below???
The knobs are for hot and cold water??

Jun 08, 2014 | Plumbing

1 Answer

Mira 88 manual mixer not supplying hot water.


You need a new cartridge for the shower located behind the handle.

Jan 26, 2014 | Home

1 Answer

Got mira discovery mixer shower. wont get hot just luke warm or cold. taps in rest of house ok? Had it off the wall recently to tile behind it but apart from that been great for 6 years. any ideas?


There should be a hot water limiter behind the knob on the shower - shingle handle, undo the handle and move the adjustment to allow more hot water. Not familiar with mira discovery mixer

Feb 03, 2013 | Home

1 Answer

I have an iflo thermostatic bar shower mixer which no longer delivers hot water for the shower. Do i need a new Bar Mixer?


To get rid of this problem, you should consult with a professional. Apart from this, you can buy attractive and best quality shower mixer by visiting this site: showerenclosures

Jan 02, 2013 | iflo Home

1 Answer

I just installed abrand new single handle delta shower faucet and the water does not get hot enough.


Many single-handle shower mixers have a hot limit, usually limiting the throw of the handle. You could go to the mfg's website (www.deltafaucet.com) & find instructions for adjusting it. Or, if you're handy, you could take off the handle & have a look; it shouldn't be too hard to see what's stopping the handle from turning more towards the hot side. Make changes in small increments & remember where you started.

Mar 01, 2011 | Delta & Single Handle Shower Faucet

1 Answer

Adjusting the scauld guard on a shower mixer valve


Uue a 1/8" allen wrench to remove handle to access the dial that set's the mixture of water.Remember or mark where it is and remove and reinsert counter clockwise about a 1/4 turn to start to you reach desired temperature setting. Be careful not to set it at a hot enough setting to burn you.
Once dial in place slide handle on and turn on to check water temperature.

Jul 31, 2010 | Delta & Single Handle Shower Faucet

1 Answer

Mira mixer cannot balance temp.either scalding hot or freezing cold


I suspect you have gravity fed hot water system and the mixer cannot balance the high pressure of the cold mains against the low pressure of the hot water.
Either install a shower pump. Means installing electrical connections and quite a bit of plumbing
Or a mechanical pressure reduction valve on the cold input pipe to the shower

Apr 02, 2010 | Legacy Home

1 Answer

Shower mixer taps


look for a scald safety screw adjustment. Remove the handle, and it is underneath. this is for safety of young children, and is factory set.

Dec 23, 2008 | Price Pfister Ashfield Single Control...

Not finding what you are looking for?
Home Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top iflo Home Experts

Donni Steen

Level 3 Expert

659 Answers

Tom Chichester

Level 3 Expert

36279 Answers

Brad Brown

Level 3 Expert

16147 Answers

Are you an iflo Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...