Question about Bosch Hammering

1 Answer

Bosch demolition hammer wont hammer

Just replaced new striker pin in hammer and it still wont hammer sufficient, can you help??

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Bosch Master
  • 1,793 Answers

MUCH NEWER BOSCH demolitionhammers have a special consumables kit you MUST use anyway its marketing technical made exactly on the calculated operating hours.

Every tools has his own kit and by the heavier models of powertools a very special lubricating oil instead of grease that was used by the older tools that are working with a slower tapping block instead of a very fast battle piece.

Posted on Feb 26, 2016

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jmgldsmth
  • 1869 Answers

SOURCE: Need manual for Hitachi Demolition Hammer

http://www.hitachipowertools.com/product/files/concrete_masonry/demolition_hammer/H65_OM.pdf

Posted on May 28, 2009

  • 142 Answers

SOURCE: Bosch demolition hammer oozing grease/oil.

Look around there for some O rings we have had this same problem with some of our Bosch hammer drills, and they usually replace a set of seals around the nose of the tool

Posted on Jul 06, 2009

  • 384 Answers

SOURCE: THE APPLIANCE IS SMOKING, Y

Y R U & ?

Posted on Sep 04, 2009

rowdy45176
  • 2176 Answers

SOURCE: dewalt demolition hammer stopped hammering.

could be a few problems, the striker could be stuck from debris or the ram might be hydraulically locked. they make a rebuild kit for this tool if you are mechanically inclined. I would suggest first going to their site and downloading a parts breakdown and there you will find what is involved and the parts listing. It is "dewaltservicenet.com" and on the left hand side type in your model number and then follow the links to download this. Let me know if you need more assistance.

Posted on Apr 23, 2011

  • 1383 Answers

SOURCE: Bosch 11316EVS demolition Hammer soft start not

Variable speed control module has failed, however you can still use the tool. Hammering action will improve with a good cleaning of internal parts and apply new grease. Hammering action is caused by air/vacuum cushion between drive piston and driven piston which inturn hits a third piston that actually impacts the bit. If third piston is worn, chipped and lodged with debris, there will be light hammering action. After use, store the hammer with the nose pointing down so that the driven piston will slide to end of cylinder and ready for next use.

Posted on Sep 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wat colour cable goes in which side inside a Bosch demolition hammer


That Depends on the model and the year of build or is it really a demolition hammer or a rotary hammer instead of a demolition hammer made much people made that mistake , the tools are different in the differend Countrys where the machines are made for , look for a manual its free for your model

https://www.boschtoolsservice.com/home.aspx?WT.ac=BT_Replacement

Jan 15, 2016 | Bosch Hammering

1 Answer

How to put oil in Hitachi H65


OIL ?? I think Hitachi has always a yellow grease lubrication
hitachi grease demolition hammer Google zoeken never seen heart of oil in Hitachi demolitions. but there could be models in your Country thats new for me .
Otherwise BOSCH HILTI and the one and only brand DUSS demolition hammers and also a few brands of Chinese hammers need oil lubrication . an expensive sinc-free hydraulic oil the same as used in some pressure washers life lasting oil but for HItachi look at the link for the grease 2 tubes a enough . good luck and dont forget the piston pin to replace with a new not only the gaskets and o-rings and also the oil and dirt seals on the front where the striking pin is that must be absolutely not air leaking because all your work burns in a few months again out . you can start all-over again.

May 15, 2014 | Hitachi H65XXX 1 - 1/8 " Hex Shank...

1 Answer

How to repair bosh 11316evs


Purchase a service kit # 1-617-000-190
This will have all the normal wear parts including brushes & new grease.
This is a fairly easy hammer to rebuild - make sure you thoroughly clean all the parts, install new rings & grease - the kit comes with a parts breakdown to help. Service Pack 1617000190 for Bosch Power Tool eReplacement Parts

Apr 15, 2014 | Bosch SDS - max Demolition Hammer 11316EVS

1 Answer

Bosch demolition hammer bearings are ceased up, how can I remove it properly to replace?


Ok here goes. Purchase or use the bearing cover nut 3613461500 that you have taken from the base of the machine. and drill a 6mm hole in it. remove the armature from the machine and measure how far the end of the armature sticks out of the bearing. then fit the cover nut onto the bearing holder and whilst supporting the cover nut use a puller or press to press the armature off the bearing through the cover nut. Replace the bearing in the holder and press the bearing and holder back onto the armature until the amount of armature shaft showing is to the same distance that measured in the first place. Hope this helps.

Dec 13, 2012 | Bosch 11316evs Elec Vs Sdsmax Demolition...

1 Answer

How do I remove the striker pin on bosch 11224VSR


If you mean the front striker pin you will need to remove the circlip up inside the spindle. You can see it through the two little holes just above the spring.

Nov 06, 2012 | Bosch 1" Sds+ Bulldog Rotary Hammer Drill...

1 Answer

I have a Bosch 0611 305034 Demolition Hammer and it has quit impacting


1 617 000 036 = a Wear and Tear part set for neccesary.

May 23, 2012 | Bosch Hammering

1 Answer

Bosch 11316EVS demolition Hammer soft start not working. Starts at full speed and does not impact until slowed down.


Variable speed control module has failed, however you can still use the tool. Hammering action will improve with a good cleaning of internal parts and apply new grease. Hammering action is caused by air/vacuum cushion between drive piston and driven piston which inturn hits a third piston that actually impacts the bit. If third piston is worn, chipped and lodged with debris, there will be light hammering action. After use, store the hammer with the nose pointing down so that the driven piston will slide to end of cylinder and ready for next use.

Sep 27, 2011 | Bosch 11316evs Elec Vs Sdsmax Demolition...

1 Answer

Bosch 11316EVS doesn't star. Power cable is good What another issue is possible?


most common problems with these units is brush replacement, or even the on/off switch, I work for a home depot tool rental and are constantly replacing the brushes.

Oct 09, 2010 | Bosch 11316evs Elec Vs Sdsmax Demolition...

1 Answer

Bosch demolition hammer oozing grease/oil.


Look around there for some O rings we have had this same problem with some of our Bosch hammer drills, and they usually replace a set of seals around the nose of the tool

Jul 05, 2009 | Bosch Hammering

Not finding what you are looking for?
Hammering Logo

Related Topics:

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Hammering Experts

John Trevino

Level 3 Expert

1383 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

snowycreek

Level 2 Expert

36 Answers

Are you a Bosch Hammering Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...