Question about LG Washing Machines

1 Answer

Lg intellowasher wf-t1081tp hot water intake slow.

Hose is clear and water pressure is fine. It seems to be clogged somewhere between the intake valve and the area where water dispenses through the detergent inlet area. There's only a trickle of hot water. Cold is fine. Is there a way to open this area to see if there's a clog or something?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Wich is connecting with inlet hose & inlet valve,,back of the machine,,thre is one filter in side the valve, remove &clean it,,pls

Posted on Apr 23, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

particleman
  • 9 Answers

SOURCE: No hot water entering

1. Make sure water comes out of the hot water hose into a bucket.
2. Check to make sure the solenoid valve is working. The buzzing is the 60Hz on the coil and can make a lot of noise if valve does not operate properly. Try blowing into the hot water port. If the solenoid is functioning properly air will move freely, if not its stuck.

Posted on Jan 10, 2008

  • 1 Answer

SOURCE: LG WF-T753A Top Loader washer hot water inlet valve

Just found this whilst looking for known issues with my machine as the cold water won't stop when filling.


http://safemanuals.com/user-guide-instructions-owner-manual/LG/WF-T753A-_E

Posted on Sep 02, 2008

stephanos18
  • 144 Answers

SOURCE: Fisher Paykel GWL11 Cold Water Not Flowing

you can swap the hot and cold valves over and see if this fixes the problem as it sound like your cold valve is faulty but not the hot valve.

Cheers

Posted on Mar 25, 2009

  • 105 Answers

SOURCE: LG WM2487 front load washer spews suds out of port on rear.

You are likely using too much detergent or the detergent is not high-efficiency detergent. Change detergents and/or lower amount and this problem should go away.

The water port on the back allows air inside the tub to escape. However, if the wrong type or quantity of detergent are used, excess suds will flow from this port.

Posted on Aug 02, 2009

SOURCE: Fisher/Paykel GWL10US washer. Blinking hot and

When they say replace the valve There,s a very good chance the diaphram is the valve is purferated or split (common Problem).But you can Remove the coil from this & with pointy nose plyers you can unscrew the top & inspect the diaphram If it,s ok give us a bit more info Hope this helps.Cheers.

Posted on Aug 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My lg intellowasher wf t8501tp won't go into a


Check the pressure switch and hose. Pressure switch is what turns the pump on and off. Trouble is usually in the hose so check it first. Look for the hose to be unattached or clogged.

Jan 13, 2013 | Washing Machines

1 Answer

I have a LG WF-T753A washing machine. The hot water is not working, but has in the past - cold water is fine. When it goes to fill up with Hot only, a slight hum, and then it stops, but no water. Have...


Check to see if the screen inside the water-inlet valve is clean. (The water-inlet valve is the device on the washing machine that the fill hoses are attached to.) If it's clean, you probably have a defective water-inlet valve. If so, completely replace it.

May 04, 2011 | LG WFT1071TP Top Load Washer

1 Answer

My water in the kitchen has a problem. When I turn the hot water on, the water pressure is very low and a load noise starts after a minute or less and the water starts to slow down. The dishwasher runs ok...


change the water inlet hose screens as they are plugged,also put the hoses on a hot water line and run hor water thru them and see what comes out of them in the sink,then replace the washer inlet hose screen

Mar 14, 2010 | Maytag Atlantis MAV6000 Top Load Washer

2 Answers

The hot water side has low water pressure. The


start by making sure the valve that supplies hot water to the sink and dish washer is fully open. If there is low hot water pressure in any of the other kitchen/bathrooms, then trace the line to see where the pressure drops. If it is only in the kitchen, it should be an old valve, (causes restriction)Good Luck.

Oct 10, 2009 | Whitehaus Kitchen Single Handle Faucet...

2 Answers

We have pressure on the cold water side but not on the hot. The faucet in the bathroom sink has hot water pressure.


make sure your water valve is working properly undo line and open valve if its working than take apart faucet and check for debri

Jul 17, 2009 | Moen 7310 Legend Single-Handle Kitchen...

1 Answer

Wld like to re-set temperature for washing to 'cold' Can't find manual. Wld like to know how to change settings. It is a 'LG Intellowasher 3.3 cu ft top loading 3 Step Turbodrum WF-T1081TP' Thank you


CLICK HERE

http://www.miaudioaddiction.com/fixya/manual.pdf

Please download asap - as it is stored on my personal FTP site, and will be removed in 48 hours.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question





Head over to the manufacturer's website.

Typically they have a SUPPORT section - where you enter the FULL model number, and then can download a FREE manual.



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Jan 04, 2009 | Washing Machines

2 Answers

LG WF-T753A Top Loader washer hot water inlet valve


Just found this whilst looking for known issues with my machine as the cold water won't stop when filling.


http://safemanuals.com/user-guide-instructions-owner-manual/LG/WF-T753A-_E

Aug 25, 2008 | LG WFT1071TP Top Load Washer

3 Answers

No hot water entering


1. Make sure water comes out of the hot water hose into a bucket.
2. Check to make sure the solenoid valve is working. The buzzing is the 60Hz on the coil and can make a lot of noise if valve does not operate properly. Try blowing into the hot water port. If the solenoid is functioning properly air will move freely, if not its stuck.

Jan 07, 2008 | LG TROMM WM2688H 4.0 cu.ft. Front Loading...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1460 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...