Question about Kyocera FS-2000D Laser Printer

3 Answers

What is C6030 on Kyocera Km-C2520 - Kyocera FS-2000D Laser Printer

Posted by on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 15 Answers

Try this:

  1. Key in 10871087
  2. 163
  3. start
  4. execute
  5. start
  6. cycle power

This will reset the code. If the code appears again you will need either a new fuser lamp or thermisters.

Posted on Feb 12, 2015

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Decompressed, rotated, relocated, or blanked-out image data does not complete within a specified period of time.TURN THE MACHINE OFF WAIT FOR SOME FEW MINUTES THAT ERROR WILL DISAPPEAR TRUST ME

Posted on Jan 27, 2015

  • kagimu joseph
    kagimu joseph Jan 27, 2015

    Fixing Thermistor Break Error. Thermistor break signal is detected for 1 sec.

×

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Kyocera Expert
  • 210 Answers

6030 Broken fuser thermistor M wire

*35/37 and 45/47 ppm printers (EUR/

USA model) only

Input from fuser thermistor M is less than

1 (A/D value) for more than 3 s.

Poor contact in the

fuser thermistor M

connector terminals.

Reinsert the connector (See page P.1-5-19).

Broken fuser

thermistor M wire./from the manual try replacing thermistors then reset the code or just replace fuser then reset the code



from the manual sadjnbdsvknsdlkvnsdv




Posted on Apr 25, 2014

  • donovin mclain
    donovin mclain Apr 25, 2014



    6030 Broken fuser thermistor M wire




    *35/37 and 45/47 ppm printers (EUR/



    USA model) only



    Input from fuser thermistor M is less than



    1 (A/D value) for more than 3 s.



    Poor contact in the



    fuser thermistor M



    connector terminals.



    Reinsert the connector (See page P.1-5-19).



    Broken fuser



    thermistor M wire.








    Try replacing the thermosters then reset the code or just replace the fuser and reset the code






    6030 Broken fuser thermistor M wire

    *35/37 and 45/47 ppm printers (EUR/

    USA model) only

    Input from fuser thermistor M is less than

    1 (A/D value) for more than 3 s.

    Poor contact in the

    fuser thermistor M

    connector terminals.

    Reinsert the connector (See page P.1-5-19).

    Broken fuser

    thermistor M wire.


    Try replacing the thermosters then reset the code or just replace the fuser and reset the code


×

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 28 Answers

SOURCE: What type of corona wire is used on Kyocera

The service manual does not specify but you will probably be ok with tungsten or oxidized. If the copies look bad with one try the other. The main charge is replaced as a whole charge assembly so I can't say that I have had to restring one.

Posted on Jul 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What type of corona wire is used on Kyocera products: FS-9520, KM-4035, KM-3530, and KM-C2520. Is it 60 Micron Oxidized?


The service manual does not specify but you will probably be ok with tungsten or oxidized. If the copies look bad with one try the other. The main charge is replaced as a whole charge assembly so I can't say that I have had to restring one.

Jul 13, 2011 | Kyocera CS-4035 Copier

1 Answer

How do I install driver for Kyocera CS 5035 on MAC


Kyocera and Copystar models are the same just replace KM with CS.

The following instructions should help you. TO download the current driver use this link to th emanufacture website; http://usa.kyoceramita.com/americas/jsp/Kyocera/resource_details.jsp?rid=18657.

Kyocera Printer Drivers and Mac OS® X 10.5 Leopard FAQ:
Is the installation for Mac OS X 10.5 the same as for Mac OS X 10.4 and earlier? Mac OS X 10.5 introduced a new printing architecture that requires changes to the installer and installation process. For this reason, Mac OS X 10.5 requires a new printer driver installer.

I cannot see my Kyocera AppleTalk® printer. How can I make it visible to OS X 10.5? AppleTalk is disabled by default in Mac OS X 10.5. Enable AppleTalk to discover your Kyocera printer.If you use the Kyocera installer, a message will appear, asking you to enable AppleTalk. Click Yes to continue the installation.

I cannot find Printer Setup Utility on Mac OS X 10.5. Is it still supported? Apple has removed Printer Setup Utility from Mac OS X 10.5. To install a printer, open System Preferences and click Print & Fax.

When I manually install a printer, multiple PPD files are listed for the same Kyocera model. Which should I choose? When manually installing a printer or changing a PPD for a installed printer, both Linux and Mac OS X PPDs are listed for some older Kyocera models due to a change in PPD handling in Mac OS X 10.5. Linux PPDs can be identified by the word Gutenprint in the PPD filenames.

Supported Multifunction Printers: KM-1650, KM-1815, KM-1820, KM-2050 ,KM-2530 ,KM-2550, KM-3035, KM-3050, KM-3530, KM-4030, KM-4035, KM-4050, KM-4530, KM-5035, KM-5050, KM-5530, KM-6030, KM-6330, KM-7530, KM-8030, KM-C830, KM-C830D, KM-C850, KM-C850D, KM-C2520, KMC2525E, KM-C2630, KM-C3225, KM-C3225E, KM-C3232, KM-C3232E, KM-C4008, KM-C4035E, CS-1650, CS-1815, CS-1820, CS-2050,CS-C2525E, CS-2550, CS-6030, or newer. Supported Printers: FS-820, FS-920, FS-1018MFP, FS-1020D, FS-1030, FS-1100, FS-1118MFP, FS-1300D, FS-1800, FS-1800+, FS-1900, FS-1920, FS-3800, FS-3820N, FS-3830N, FS-6020, FS-6026, FS-9100DN, FS-9120DN, FS-9500DN, FS-9520DN, FS-C5016N, FS-C5020N, FS-C5030N, FS-C8008N, FS-C8026N, FS-C8100DN, or newer.

I hope this is helpful,
Shawn

Mar 08, 2011 | Kyocera Copystar CS-5035 Copier

2 Answers

KM-2050 Printer: i need to find the pin number to my kyocera km-205...


I need to create a new pin on kyocera 5050 machine as the old one is lost

May 05, 2010 | Kyocera Mita KM-2050 Printer

2 Answers

How to fix Error code C6020


I have The Km C2520 with the same C6020 code. Is the solution the same?

Jan 26, 2010 | Kyocera Mita KM-1815 All-In-One Laser...

1 Answer

I have a copystar c2520 and am getting a c6000 error which was cleared with 10871087 and then 163 but now im getting a c6030 code and it will not clear. could this be that the fuser is no good?


C6000, С6030 is Abnormally high temperature in the fixing section – The fixing unit thermistor output voltage remains less than 0.5 V for longer than 1 s, indicating the fixing temperature rises above 536F this may be the fuser is no good. Sorry? coll to Servise center Mita. Dood lack!

Sep 22, 2009 | Copystar Office Equipment & Supplies

1 Answer

Getting an error code of C6030


KM-5050 error code displaying C 6030 how can i remove this code WebRepOverall ratingThis site has no rating(not enough votes)

Apr 16, 2009 | Office Equipment & Supplies

2 Answers

Kyocera km-2050 scanning function


The km 2050 was on network, but moved to home and directly into tower system via usb interface connector. Printer works, but can not get scanner to work? read instructions without a clue. can someone help with correct proceedure?

Mar 04, 2009 | Kyocera Mita KM-2050 Printer

1 Answer

We are trying to print out the maintenance or service schedule.


If you want some general info on drum count, dev drive time etc you can put in the following codes whilst in copy mode,

1087 1087 
000 will appear on the screen
press the green start button to activate
on the touch screen select maintenance and press the green button again

Jan 23, 2009 | Office Equipment & Supplies

2 Answers

SYSTEM ERROR


error 610 machine kyocera km-3035 ????

Nov 05, 2008 | Kyocera Mita KM-3035 All-In-One Laser...

Not finding what you are looking for?
Kyocera FS-2000D Laser Printer Logo

207 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kyocera Office Equipment & Supplies Experts

Kyocera HP Expert

Level 3 Expert

523 Answers

Chris Schutte

Level 2 Expert

51 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

Are you a Kyocera Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...