Question about Kenmore Washing Machines

1 Answer

Washer won't stay on heavy duty setting, keeps reverting to regul

My Kenmore washer Model # 11020052994 will not wash on the heavy duty setting. It keeps returning back to regular setting. A code No. F3 keeps coming on. I have replaced the control board and it washes all the way through on the reg. cycle but will not wash on heavy duty.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

The problem with the fabric softener not dispensing is not likely related to and F03 error code due to the washer not draining.

For the dispenser problem, I recommend that you pull the dispenser drawer out and clean it thoroughly.
The fabric softener dispenser works on a siphoning principle.
Make sure that the siphon hole in the dispenser is clear and not restricted or plugged.

You can fill the fabric softener compartment with water and make sure that it is siphoning properly while you are cleaning it.
Make sure that the cover is properly replaced on the fabric softener dispenser when the drawer is replaced in the washer.
You can use the diagnostic test described below to test the fabric softener dispenser.
If the softener dispenser does not fill and dispense properly, you could have a failed dispenser valve, a failed control board or a wiring failure between components.

You indicated that you tested the pump and that it is good. You could have a clogged drain hose or a clogged washer drain that would prevent the washer from draining.
You could also have a failed drain pump even though it runs. If the impeller is jammed or damaged, it will not pump out the water in the washer.
You will likely need to unplug the washer and drain the water out of the tub using a wet/dry shop vacuum.
To check the pump and drain hose at the bottom of the washer, remove the bottom front service panel and remove the drain pump. You may find a clog or restriction in the drain pump or connecting hoses. If the drain pump is damaged or will not work, it will need to be replaced.



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question!!!!

Posted on Sep 17, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore heavy duty 70 series model 110-8237012


probably your drain pump leaking it has a seal right where it attaches to motor,,,,mine is leaking there but haven't replaced it yet! lol

Feb 27, 2010 | Kenmore Washing Machines

2 Answers

What is the capacity of my Kenmore 80 series Model 110 washer?


The cubic feet of the Kenmore washer model 110 heavy duty is 2.8 cubic feet. Measured to the top water line 14.5 inches and using the radius of the tub of 10.375 inches

Sep 08, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore washing Machine Mod. 11020052994 will not wash on heavyd


The problem with the fabric softener not dispensing is not likely related to and F03 error code due to the washer not draining.

For the dispenser problem, I recommend that you pull the dispenser drawer out and clean it thoroughly.
The fabric softener dispenser works on a siphoning principle.
Make sure that the siphon hole in the dispenser is clear and not restricted or plugged.

You can fill the fabric softener compartment with water and make sure that it is siphoning properly while you are cleaning it.
Make sure that the cover is properly replaced on the fabric softener dispenser when the drawer is replaced in the washer.
You can use the diagnostic test described below to test the fabric softener dispenser.
If the softener dispenser does not fill and dispense properly, you could have a failed dispenser valve, a failed control board or a wiring failure between components.

You indicated that you tested the pump and that it is good. You could have a clogged drain hose or a clogged washer drain that would prevent the washer from draining.
You could also have a failed drain pump even though it runs. If the impeller is jammed or damaged, it will not pump out the water in the washer.
You will likely need to unplug the washer and drain the water out of the tub using a wet/dry shop vacuum.
To check the pump and drain hose at the bottom of the washer, remove the bottom front service panel and remove the drain pump. You may find a clog or restriction in the drain pump or connecting hoses. If the drain pump is damaged or will not work, it will need to be replaced.



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Jun 17, 2009 | Kenmore Washing Machines

1 Answer

Kenmore Heavy Duty Washer Leaking from bottom


Probably the drain pump seal has gone bad.
Check it for leaks.
If your floor is good and level look for water near the front center of the machine.

Feb 25, 2009 | GE WHRE5260E Top Load Washer

1 Answer

How do I replace a lid switch on a kenmore heavy duty washer model # 22442 my switch is in pieces


I just stuck a wooden clothes pin in the hole to keep the little level in check. My landlord's washer had that problem and he didn't want to pay to fix it. It ran great for many more years after I stuck the wooden clothes pin in it.

Feb 24, 2009 | Kenmore 22442 Top Load Washer

1 Answer

Washer will not go to the rinse cycel.


check cold water line...onthejob,,,im assuming no rinse cycle only..onthejob,,,no mater the cycle

Jan 31, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

Kenmore series 80 washer only works on heavy duty cycle.


bad transmission,,check voltage...below 110 with load and water pressure switch or hose defective..

Dec 24, 2008 | Kenmore 24902 Top Load Washer

1 Answer

Speed Control only works in Heavy Duty


sound like your motor is going out ,,,, the wiring at the motor may also be loose from out of balance loads

Nov 23, 2008 | Kenmore 24032\24036 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Sal DeAngelo

Level 3 Expert

2180 Answers

fordexpert

Level 3 Expert

5520 Answers

Ed Mac

Level 3 Expert

731 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...