Question about DISH Network DVR 510 DTV Receiver / 100-Hours Video Recorder

1 Answer

TV showed "Problem Detected" with a possible solution of unplugging my unit for 60 secs. and allowing it to reboot. I do this routinely (Once a mo), but did it again. This time it cleared ALL recorded items (including protected items) I had 43 hours available for recording. It also Cleared all scheduled timers, and now will not allow me to record if I try to use "Create A timer" or "Create a Scedule". Is my harddrive fried?? (I've had problems with it locking up for about the last 12 months) Dish Network DVR

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • DISH Network Expert
  • 246 Answers

Hi ljdubas myname is Mike Houston of DISH Network and I was going over your post and if youare getting the "problem has been detected" and it still comes up after youunplug the receiver and plug it back in there is a problem with the DVR and itwill need to be replaced.

Posted on Feb 13, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Whirlpool duet front load washer model # GHW9150PWD. I have an error code of F 02 and SUD. I have so far cleaned the filter and the lines, replaced the pump, replaced the water pressure swith and...


6 - 1
DIAGNOSIS & TROUBLESHOOTING
SUDS DETECTION
During Drain Routine
During the Drain Routine, the water level is checked continuously. Normal drain will occur until the
pressure switch senses no water in the wash tub and there is no foam (suds). The drain pump will
operate an additional 15 seconds after the pressure switch reports no water or foam.
If the drain routine operates for four (4) minutes and the pressure switch senses any foam (suds) in
the wash tub, the Central Control Unit will start the "Kill-Foam" Routine. (See description of this
Routine below.) After the Kill-foam Routine is concluded, the Drain Routine will restart. If, after
four (4) minutes the pressure switch still senses foam in the wash tub, the Central Control Unit will
go into Failure Mode. The digital display will show, F02.
During Spin (Extract) Routine
During the Spin/Extract Routine the water level is checked continuously. If, during this routine, the
pressure switch senses the presence of foam (suds) in the wash tub, the Central Control Unit will
stop the drive motor and the basket will stop spinning. The electronic control will count the number
of spin repetitions that are attempted due to foam (suds). There are a maximum of three (3)
attempts for each Spin/Extract Routine.
Kill-Foam Routine
1.
The Remaining Time counter is stopped.
2.
The digital display shows Sud.
3.
The Drain Pump is turned OFF.
4.
The Central Control Unit will fill the wash tub with 1 gal. (4 L) of cold water.
5.
While the tub is filling the basket will tumble 1 sec. ON/15 Sec. OFF.
6.
Once the tub is filled, the drive motor will turn OFF and the basket will rest without any
movement for five (5) minutes.
7.
After the five (5) minute rest, the remaining time counter will restart and the digital display
will show the remaining time left in the routine.
NOTE:
If the Kill-Foam routine was initiated during a Spin/Extract Routine, the tumbling action
will be reduced to a cycle of 3 sec. ON/13 sec. OFF. If, at the end of either the Drain or Spin/
Extract Routines, a suds condition still remains, the digital display will show Sud.
Sud will also be displayed for a short period at the end of a cycle, if a Suds condition was
detected during the cycle. This will alert the consumer to reduce the amount of detergent in
subsequent uses MANUAL

Oct 31, 2013 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Hard reset philips tv


A hard reset (reboot) is achieved when the television is unplugged while on. The unit should remained unplugged for at least 60 seconds.

Nov 18, 2012 | Philips 32PFL5403D/27 32 in. LCD TV

1 Answer

Amp error pioneer


Hi pat,

For pioneer Amp error:

It means that microprocessor has detected an abnormal DC voltage:

Speaker relay will be Off, then flash "AMP_ERR" on display.

If the AC plug is pulled off within 60 sec,

and then it is plugged in again, the unit will be reset for 60 sec.

Oct 19, 2012 | Pioneer Vsx-d811s Audio Video Multi-...

1 Answer

Electrolux dishwasher DF code after an er 01 code. how to fix at home


Hello Shirley - Typically error code ER01 indicates that a water leak is detected under the tub. Unit will possibly need a hydraulic kit. Try unplugging the unit or flipping the household circuit breaker off. Wait approximately ten minutes and turn the unit back on. Could the error code DF possibly be PF? If so, PF means power failure and you should be able to start a cycle. If the error code continues to display on dishwasher then I suggest contacting a professional to accurately diagnose and repair it.

Sep 30, 2012 | Electrolux EIDW6305GB 24 in. Built-in...

2 Answers

The unit turns on and off every 40 sec. or so. I have turned the unit off and on and I get a red light blicking 5 times on and off. this happened about 4 to 6 mo. ago and it is happening again...


Hi,
Below info are related to Sony KDF-E60A20 lcd projection tv.
5 times red light blinking indicates problem with lamp drive circuit (ballast supply board) that is not producing high voltage for lamp to generate high bright white light.
Check/ replace ballast supply board in above mode tv to solve this problem.
If you tv model is different, let me know to provide you related info.
Thanks

Jan 17, 2011 | Sony KDF-E60A20 60 in. LCD HDTV

1 Answer

Washing machine stopped and says "sud". What does that mean?


SUDS DETECTION

During Drain Routine

During the Drain Routine, the water level is checked continuously. Normal drain will occur until the

pressure switch senses no water in the wash tub and there is no foam (suds). The drain pump will

operate an additional 15 seconds after the pressure switch reports no water or foam.

If the drain routine operates for four (4) minutes and the pressure switch senses any foam (suds) in

the wash tub, the Central Control Unit will start the "Kill-Foam" Routine. (See description of this

Routine below.) After the Kill-foam Routine is concluded, the Drain Routine will restart. If, after

four (4) minutes the pressure switch still senses foam in the wash tub, the Central Control Unit will

go into Failure Mode. The digital display will show, F02.

During Spin (Extract) Routine

During the Spin/Extract Routine the water level is checked continuously. If, during this routine, the

pressure switch senses the presence of foam (suds) in the wash tub, the Central Control Unit will

stop the drive motor and the basket will stop spinning. The electronic control will count the number

of spin repetitions that are attempted due to foam (suds). There are a maximum of three (3)

attempts for each Spin/Extract Routine.

Kill-Foam Routine

1. The Remaining Time counter is stopped.

2. The digital display shows Sud.

3. The Drain Pump is turned OFF.

4. The Central Control Unit will fill the wash tub with 1 gal. (4 L) of cold water.

5. While the tub is filling the basket will tumble 1 sec. ON/15 Sec. OFF.

6. Once the tub is filled, the drive motor will turn OFF and the basket will rest without any

movement for five (5) minutes.

7. After the five (5) minute rest, the remaining time counter will restart and the digital display

will show the remaining time left in the routine.

NOTE: If the Kill-Foam routine was initiated during a Spin/Extract Routine, the tumbling action

will be reduced to a cycle of 3 sec. ON/13 sec. OFF. If, at the end of either the Drain or Spin/

Extract Routines, a suds condition still remains, the digital display will show Sud.

Sud will also be displayed for a short period at the end of a cycle, if a Suds condition was

detected during the cycle. This will alert the consumer to reduce the amount of detergent in
subsequent uses.

Oct 07, 2010 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

No picture or sound?? status light flashes in four blinking intervals. I was told it could possibly be the lamp it has never been replaced.


The STANDBY light will flash if an issue is detected within the television. This can sometimes be resolved by simply following the steps below to reset the television.
  1. Turn off the television.IMPORTANT: For a projection television that uses an internal lamp, wait 5 minutes after turning off the television to allow the lamp to cool before continuing with the following steps.
  2. Unplug the television power cord from the electrical outlet.
  3. Let the television remain without power for 60 seconds.
  4. Plug the power cord back into the electrical outlet.NOTE: If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.
  5. Turn on the television.

Aug 08, 2009 | Sony KDS-R60XBR1 60" Projection HDTV

1 Answer

Cold Start Up Low Squeal


If you can solder, try checking all the boards for poor solder connections. Resolder any that appear grainy or have rings. If that fails to resolve the problem, then we will have to start looking for failing capacitors in the power supply area.

Please note that there are potentially dangerous high voltages inside the set even when unplugged.

Keep us posted,
Dan

Feb 20, 2009 | Toshiba 42HM66 42" Projection HDTV

1 Answer

Can't connect Motorola sb5100 to a Linksys wrt54g


Make sure that you have the ethernet cord from your modem plugged into the WAN/Internet port on your router. Then unplug the power cord from your cable modem and plug it right back in. After the modem fully comes back online, unplug the power cord on the wireless router and plug it back in. wait 30 - 60 sec and then try and connect.

Most cable companies only allow one active"CPE" at a time for internet access. All this means is when you change what is connected to the cable modem you must always reboot the cable modem to allow access.


Hope this helps. Let me know if it does not work.

Please Rate

Jan 29, 2009 | Arris SB5100 SURFboard DOCSIS 2.0 Cable...

1 Answer

I HAVING PROBLEMS WITH MY CABLE TV. MY DVR WILL NOT COME UP AND ALL MY CHANNLES IS SHOWING NOT AVAILABLE AND MY ON DEMAND DISPLAYS AN ERROR MESSAGE AND I PAY MY BILL 2 WEEKS AGO AND NOTICE THAT THE POWER...


Good Day, albertgaw;
Since TV is showing an image I would suspect the cable/sat box. Try rebooting box again, unplug or hold power button in for 5-8 seconds, be patient and allow several minutes to allow box to reset. If no fix call your provider to resend the signal, or arrange to have box replaced.
Good Luck, big IRISH.

Jul 15, 2008 | Televison & Video

Not finding what you are looking for?
Televison & Video Logo

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top DISH Network Televison & Video Experts

S. Gontko

Level 2 Expert

142 Answers

john milligan

Level 3 Expert

514 Answers

Jaime Hernandez

Level 3 Expert

2318 Answers

Are you a DISH Network Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...