Question about Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Maytag neptune TL

I have a maytag neptune TL and there are several things wrong with it...1. I can't wash small loads it will stop at the spin cycle and flash dc and 2. it will wash fine on regular loads until it comes to spin cycle again and it will stop and flash nf 3. my fabric softener dispenser will not let the softener out neither will the bleach dispenser.....can anyone help me will my dilemas???? thank you

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 335 Answers

The machine needs to cut you a break;

“”i have a maytag neptune TL and there are several things wrong with it...1. I can't wash small loads it will stop at the spin cycle and flash dc””

This issue is a clutch issue see this post to DIY the repair.

“”it will wash fine on regular loads until it comes to spin cycle again and it will stop and flash nf””

This one is a little confusing the “nf” error is a No water fill error code. Check these two post for support regarding water inlet restriction or valve not opening properly.

nf post nf post 2

“”my fabric softener dispenser will not let the softener out neither will the bleach dispenser””

See this fabric softer post for support. The fabric softener dispenser may be clogged or the water dispenser valves feeding both dispensers may not be operating properly. The Service Manual on page 16 “Board Output Test” will give you support to turn on the Fabric Softener Valve and Bleach valve. See if you hear the valves operate in Service Mode”

My method may seem a little confusion for viewing water flow to the dispensers. This issue could be associated to the nf error you are receiving, restricted water flow (inlet screen clog) or cold water valve not working properly.

Post back for any questions or possible support I can offer. I’m an owner like you not a repair person but I’m very comfortable working on this machine. Rich

Posted on Jun 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wash cycle are running to long


FIXED Maytag Neptune, Timer Problem - ApplianceBlog

www.applianceblog.com/.../23387-Maytag-Neptune-Timer-Problem

Mar 4, 2011 - 8 posts - ‎3 authors
My countdown timer is stuck at the 33-minute level in the "wash cycle", and repeatedlyruns for a 30-40 seconds, then stops, then runs, then ... Maytag Neptune TL Washing Machine stops in spin cycle ...
10 posts
Jul 25, 2013
Maytag Neptune Washer Won't Spin/drain
7 posts
Jul 4, 2013
Neptune TL Washer FAV6800AWW - DC and UC ...
5 posts
Jul 3, 2007
MAYTAG NEPTUNE WASHER CONTROL PANEL ...
8 posts
Jun 29, 2005
More results from www.applianceblog.com

Troubleshooting a Too-Long Wash Cycle - whirlpool washingmachine ...

ask.metafilter.com/233920/Troubleshooting-a-TooLong-Wash-Cycle
Jan 25, 2013 - We have a Whirlpool Duet washing machine (about 2 years old). Thecycle is taking WAY too long to complete. The load that's running now ...

Maytag Neptune washer repair: motor/motor control circuit ...

? 12:10
https://www.youtube.com/watch?v=ITTbDh8CFEU
Dec 11, 2013 - Uploaded by daytonaturbofreak
Maytag Neptune washer motor/motor control circuit board ... my board just fried - is your washer still working? wondering how longthe conversion fix will last. ... Other times it will run a completecycle without any malfunctions.

Jan 11, 2016 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

We just moved and the house came with a Maytag Neptune TL which won't spin if there are clothes in the cylinder. It will spin empty. Please help! Thanks.


Washer bangs around in spin cycle and throws a DC or UC unballance code with cloths in the wash basket is that correct?

If so it's a Clutch issue.

If you want read more about what I feel is your issue read this post Maytag Neptune load unbalance

Sep 08, 2011 | Maytag Neptune FAV6800AW Top Load Washer

2 Answers

Maytag neptune top load washer will not spin out with small loads, large loads are fine. I get the DC error at about 10 mins left in spin cycle. No amount of shifting load will solve problem


This is a Clutch issue could be a easy fix if the Tub Seal is not the root cause.

If you get no help at this forum Google This ""Neptune TL Washer FAV6800AWW""

5th post down you will find the SM and support for the "DC and UC" unbalance error codes. Good luck..............DH1200s

Aug 20, 2011 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

I have the neptune tl. When it gets to the spin cycle it stops and flashes dc in the display. I have to reclick the start button to get it to continue and finish. Any ideas? I was reading online all...


Our washer was doing the same thing. A repairman looked at today and said it's a transmission or brake problem but it may be under warranty for the parts--the warranty is for 10 years.

Dec 25, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

My Maytag will not run a complete cycle. Is there


mgissy


What is your machine model number? Is it a FAV6800A or FAV9800A TL?


If it’s a FAV6800A or FAV9800A TL do you error out in the Spin cycle of the wash cycle with an unbalance error code such as dC or uC? Is the wsh tub banging around during Spin Cycle of the Wash Cycle?

If so see this post Clutch Fix. I have a step by step maintenance/repair process for Clutch Pulley assembly issues related to the above error codes.

Post back if you have questions or concerns………Rich

May 03, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Neptune tl washer will go half way threw cyle,start to spin,stop and start to spin,stop and start to spin .tried to unplug it restart and nothin, tried different settings still nothing. tried moving the...


If your machine is a FAV6800A to FAV9800A here is the Service Manual.
If it one of those machines I suspect a possible clutch malfunction.


See this post for what is involved to do clutch maintenance or replacement.


Do you have any error codes to the display if it's a FAV6800A such as dC or uC unbalance codes. Is the wash tub banging around on Spin Cycle of the Wash Cycle? ……Rich

Feb 06, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Wont Finish Spinning stops and Flashed DC


If the machine type is a FAV6800A/FAV9800A see this Clutch repair post if you want to DIY. You will find links to the Service Manual and parts info if needed.

You can check out the TDS but I would go right to the Clutch repair post if the machine shuts down in with a error code dC or uC.

That means the TDS is producing analog voltage swings +3.5VDC to 0VDC to the input of the Control Board Conn_P3 pins 10 and 11. Those DC voltage swings are at the design limit of max Wash Tub movement and the Control Board shuts the Spin Cycle down……..so thebTDS is working as designed.

The machine will make several attempts to redistribute the load before error code generation failing with dC or uC error codes.

Post back if you have questions any DIY'er with basic skill sets can do the Cluch maintenance/repair.....Rich

Jan 04, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Neptune won't advance from Rinse to SPIN


If the clutch fails the first thing noticed is a UC or DC error displayed and there is no drain or spin.

If you are seeing the above error and having a problem with spin and drain then the most likely cause of this is the clutch. The clutch fails to lock down the spinners and the basket is unable to go into spin and without a 90 RPM there is no drain.

Replace the clutch.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question(@#$^

Aug 01, 2008 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Neptune won't advance from Rinse to SPIN


If the clutch fails the first thing noticed is a UC or DC error displayed and there is no drain or spin.

If you are seeing the above error and having a problem with spin and drain then the most likely cause of this is the clutch. The clutch fails to lock down the spinners and the basket is unable to go into spin and without a 90 RPM there is no drain.

Replace the clutch.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Mar 10, 2008 | Maytag MAH6500 Neptune Front Loading...

Not finding what you are looking for?
Maytag Neptune FAV6800AW Top Load Washer Logo

1,048 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...