Question about Gaggenau EB294/295 Electric Double Oven

1 Answer

Huh? - Gaggenau EB294/295 Electric Double Oven

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,197 Answers

No its huh??????

Posted on Jun 16, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

F3 code I have replaced 2 high voltage transformers,2 caps,2 mags,2 lo voltage transformers, 3 relays, and I/O board. and still have a F3, i have reprogramed the I/O board twice and my amp clamp reads 15.1...

holy **** that was a very expencive fix huh. I hope you spent the 50 bucks and have a service manual. What about the diodes, have you tested or changed those. That looks like the last thing i would change and there only a few bucks so i would change them at this point anyway. Are you blowing a fuse at all.
You need to narrow the problem down, not just toss money into the toilet replacing good parts. If your reading 15.1 amps then you have no problem in the high voltage system. Unless the amps are ramping or erratic. Your I/O board is bad if its reading 15.1 and triggering an f-3 fault. You said you replaced it though. Contact who you purchased it from and see if they will help. Its a $420 board and $160 for each HV Transformer they should help. I would guess that your I/O board it bad. You also said you changed relays. Did you change the K2 relay.
Hope you can solve the problem quick. Hopefully this helps

Nov 03, 2010 | TurboChef TORNADO Electric Oven

1 Answer

Controls work fine , element glows red, but stove dorsnt light, huh.

Ok, I'm assuming the element is the ignitor right? The trick here is the ignitor, if it's a glow type. The ignitor must decrease it's resistance enough to allow the gas valve to receive it's calibrated min current to open. If the ignitor is bad it can glow just fine but if the intensity is not sufficient, the resistance will not be decreased enough to trigger the gas valve. Sorry to get complicated. I would replace the ignitor first and go from there. Hope this helps.

Western Appliance Repair
Appliance Repair Meridian

Oct 09, 2010 | Frigidaire FEB27S5A Electric Single Oven

1 Answer

My sears model 911.9579980 oven won't work. everything else works. one repair person said that I needed the capasitor. He said that he had trouble getting the right part for that model. what is your...

Huh?? That is not making any sense to me...
I tried running the model number you gave and it is not coming up... so something is amiss there... however I see NO capacitors even on the list for ovens close to yours...and usually there are no capacitors in an oven...
I would get another opinion....
BTW is your oven gas or electric??? from what I could find it could be either one...


Sep 16, 2010 | Kenmore Ovens

1 Answer


UNPLUG the stove. It sounds like the cord has a problem, possibly one of the wires has broken and is shorting out. Have a qualified person check it out.

Dec 27, 2009 | Kenmore Ovens

1 Answer

How to self clean a 1989 model self clean GE oven How do I set?

I found that you cannot turn the CLEAN knobs both off before you release the latch on the door. You cannot unlatch the door
if the Oven Set knob is turned from Clean to must still be on Clean to unlatch....simple, huh? Well, it was confusing
at the time!

Dec 01, 2009 | GE Ovens

1 Answer

Electronic Display Problem

you can check your manual if ariund for possible 5 year warr on electronics. if so they will still require an authorized servicer to replace they wont ship to you. and all ercs are different so ordered as needed.

Mar 14, 2008 | Jenn-Air JJW9627C Expressions Collection...

Not finding what you are looking for?
Gaggenau EB294/295 Electric Double Oven Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Gaggenau Ovens Experts

Dennis Boxerman

Level 3 Expert

1262 Answers

Jaime Hernandez

Level 3 Expert

2336 Answers

Oloyede Monsuru

Level 3 Expert

1417 Answers

Are you a Gaggenau Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides