Question about Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

2 Answers

Hover steam vac Model #F5897-900

Need instruction manual and problem priming the upostery hose

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

When I use my Hover Steam Vac, it smells like rubber is burning. How do I fix this?

Posted on Jun 16, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 25 Answers

Sounds like you may need a new belt

Posted on Jun 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Upon powering up suction is low. Needs to be primed with hand on hose intake; then full suction comes back.


Turn the vacuum on without the hose.If this continues the motor may need armature brushes or the motor itself may be burned out...motors are not too expensive,I usually put "Lamb" motors in for around 139.00....Chris

May 12, 2015 | Electrolux Central Vacuum

2 Answers

I have a modelF5914-900 steamvac cleaner.serial #0704 0011 4711 I cleaned the carpets in my house and then started to do the stairs with the stair attachment. I got down to the last four stairs and the...


Check the hose. Take the hose off the vacuum cleaner, if possible. If the clog doesn't shake out, try running something down the hose. Don't poke a hole in the hose.

Apr 13, 2008 | Vacuums

1 Answer

How do you replace the tool hose on a Bissell Pro Heat 2X?


Here is the Instruction or User Manual for the 7910 and the 8910 series machines

Here is the Instruction or User Manual for the 8920, 9200, 9300, 9400, series machines

Here is the Instruction or User Manual for the 9500 series machines

Jul 03, 2013 | Vacuums

2 Answers

Can any one send me a diagram of the internal water and soap connection for A Bissell proheat carpet cleaner Model #7901-1. i imagine pump also needs to be primed, which port do I use to do this. Thank you...


Click here for the manual - We think this will guide you,
As for the pump / port to be primed -
For Prime and loss of prime please click HERE -

From what Bissell says you must prime both - please read page 7 especially.

This should get you good to go.
Gary
142d81e.jpg

Apr 10, 2010 | Bissell 7901-1 ProHeat Scotchgard Upright...

2 Answers

Cant get any water to floor or hand dispenser on my bissell power pro steam cleaner


That means that the pump belt is worn or stretched and needs to be replaced. Here is a link to the belt you need and the manual which has instructions:

Bissell ProHeat Belt and Manual

Dec 12, 2009 | Bissell 1697-7 Powersteamer Pro Deluxe...

1 Answer

No suction for upholstery hose


http://www.hoover.com/pdfs/manuals/F5914900.pdf try priming your hose

Before using tool
It may be necessary to remove air from
the system (“prime the pump”) so the
clean solution will flow to the tool. Follow
these steps:
1. Attach tool to hose and turn the carpet
cleaner ON.
2. Put the tool on a hard surface or
against your hand to block off the suction.
3. Wait a few seconds (can take up to
15 seconds). Then squeeze the trigger
and begin cleaning.
Follow the instructions on pages 14 and
15 for the appropriate cleaning task.

Godbless

Jun 18, 2009 | Hoover SteamVac F5914-900 SpinScrub...

1 Answer

My hoover steam vac is not releasing the cleaner


http://www.hoover.com/pdfs/manuals/F5914900.pdf this is the manual for your model

Godbless

Problem: Clean solution won’t
dispense
Problem: Brushes/brush indicator
won’t rotate during floor cleaning
Possible cause
Possible solution
• Not firmly plugged in
• Plug unit in firmly
• No voltage In wall plug
• Check fuse or breaker
• Blown fuse/tripped breaker
• Replace fuse/reset breaker
Possible cause
Possible solution
• Recovery tank full/automatic
shut off engaged
• Remove and empty recovery tank
• Blockage In tool on end of hose
• Remove tool and clear blockage
• Recovery tank lid not on
correctly
• Make sure lid is on securely
• Recovery tank front panel not
replaced after stair or upholstery
cleaning
• Replace recovery tank front panel
(page 14)
Possible cause
Possible solution
• Solution tank not firmly in place
• Make sure tank is securely locked in
position
• Solution tank empty
• Refill tank according to instructions for
surface being cleaned
• Recovery tank lid not on
correctly
• Make sure lid is firmly in place
• Pump needs to be “primed” (when
using tool)
• See “Before using tool” section, p. 13

Jun 15, 2009 | Hoover SteamVac F5914-900 SpinScrub...

Not finding what you are looking for?
Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum Logo

532 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Jim Parker
Jim Parker

Level 3 Expert

1041 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Are you a Hoover Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...