Question about IBM Office Equipment & Supplies

1 Answer

IBM Selectric II Ribbon Not Advancing

I have an IBM Selectric II. When I replaced the ribbon recently, the new ribbon will not advance. If I advance it manually, it will type until the ink on the ribbon wears off. Please help me. Thank you.

Posted by on

  • Diane Peters Jun 16, 2009

    Thank you. It's moving again, not freely yet but I will keep up with it. It is advancing the ribbon and typing again. Thank you for your help.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • IBM Master
  • 3,594 Answers

First check to be sure that the ribbon is on the left of the shock wire where it comes out of the cassette, if that is OK then check the ribbon driver it should move freely and swing to the ribbon take up spool. Some WD40 will free it up. Also be sire the ribbon is winding in the direction of the arrows.

DickyO

Posted on Jun 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a IBM Model 5651 Memory Typewriter (Selectric II carriage), and I cannot make the ribbon advance while typing. If I turn the ribbon it will type until the ‘ink’ runs out. It’s just not advancing. ...


If this takes a selectric II ribbon the Spiked driver may be gummed up. Remove the ribbon,
find the latch that holds the ribbon mech. open, release it the ribbon drive should swing freely to the right, if not spray some WD40 on the pivot point, above and below the arm then work it back and forth it should free up.

DickyO

Oct 25, 2010 | IBM Office Equipment & Supplies

1 Answer

Selectric II- changed the ribbon, new ribbon won't advance


The ribbon is probably not threaded to the lift of the white slacker finger just left of where it comes out of the cassette.

DickyO

Sep 30, 2009 | Lexmark Wheelwriter 15 Series II...

1 Answer

I have an IBM Selectric II. It types but does


The tab tensioner on the R. side is probably broken, not a bad job but you have to know how.

DickyO

Sep 12, 2009 | IBM Office Equipment & Supplies

1 Answer

IBM Selectric II Will type letters, but will


Several possible causes. Needs lubrication most commonly. Sometimes the velocity cable is hung up on the left side and under the carriage. remove the ribbon and shine a light down on the left side and look for a cable hung up on the pulley, make a hook with a paper clip and lift the cable up and past the pulley

I’m happy to help further over the phone at https://www.6ya.com/expert/jayw_0e86fb055a7b73de

Aug 31, 2009 | Office Equipment & Supplies

1 Answer

IBM Correcting Selectric II; correction ribbon frozen in front of typing ribbon.


Move the grey lever on the R. side of the carrier to the R. and remove correction tape, try the machine, if it seems to work OK install a new correction tape.

DickyO

May 28, 2009 | IBM Wheelwriter 30 Typewriter

3 Answers

Don't know how to load and string the ribbon on an ibm selectric


Selectric III has two different ribbons the selectric II ribbon tha the ribbon guides are part of the macine and the "bicycle" ribbon that has the guides bilt into the ribbon. to replace the "bicycle" ribbon move pull the red lever on the right toward you, drop the ribbon in turn the knob a few times in the direction of the arrows, move the red lever back done.
The other style move the lever, drop the ribbon in, be sure the ribbon is left of the slacker finger sticking up on the left,thread it tru the guides, turn the knob inthe direction of the arrows, move red lever back,done.

DickyO

Feb 24, 2009 | IBM Wheelwriter 30 Typewriter

2 Answers

Ribbon not advancing on Selectric II typewriter


on the left far side of the ribbon there is a white vertical post. the ribbon should be on the left side of that. also make sure you turn the ribbon the direction of the arrow (on the cassete) otherwise will need professional repair

Nov 18, 2008 | Office Equipment & Supplies

1 Answer

Correction tape problem IBM Selectric II


Take off the ribbon, just inside the rt. side frame of the printer is the mech. for L/O feeding. There is an arm that moves back and allows the feed to ****, that mech. is probably gummy, lube with some WD40 on both sides of the printer (the left side sets up correction lifting.

DickyO

May 19, 2008 | Lexmark Wheelwriter 15 Series II...

1 Answer

IBM Selectric III - ribbon won't turn


Make sure the ribbon cartridge lever is closed and that the ribbon is on the outside of the shock wire (where the ribbon exits the left side of the cartridge)

Jan 20, 2008 | Lexmark Wheelwriter 15 Series II...

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

1,393 people viewed this question

Ask a Question

Usually answered in minutes!

Top IBM Office Equipment & Supplies Experts

James Cagle
James Cagle

Level 2 Expert

478 Answers

Don  Farrell
Don Farrell

Level 3 Expert

1018 Answers

jasbo
jasbo

Level 3 Expert

2237 Answers

Are you an IBM Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...