Question about EXPOBAR Coffee Makers & Espresso Machines

Open Question

I have an expobar(stafco) 2003 fully auto with built in grinder with onlf free flow button working, a new control panel has been fitted (gicar 1d5e) i feel there is a fault either with the flow meter or wiring(as someone has bodged it before i got it) I need a wiring diagram for this machine if anyone can help?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 150 Answers

SOURCE: Hoover 700LB top loading washing machine

there should be a wiring diagram on board in an envelope or taped somewhere you can get one from sears too

Posted on May 08, 2008

Ad
  • 208 Answers

SOURCE: 97 honda accord v6 luxury cruise control not working

Yes, it probably is the brake switch. It must be working properly for the cruise control to work. If the part you got did not come from a car with cruise control, it will only have two electrical posts and not the four that you need.
If it is the right part, it must be turned in until the button is pushed completely, but not so far that it begins to actuate the master cylinder. Please report your results.

Posted on Aug 18, 2008

Powerman
  • 68 Answers

SOURCE: Wiring diagram for jtp18

Call GE at 1-800-626-2005 to get a wiring diagram
Regards,
Powerman

Posted on Oct 31, 2008

  • 1 Answer

SOURCE: Saeko Italia - Water flow is very slow

We repeated the de-scaling and it seems to have taken care of the problem.  (at least for now!) Maybe there was a build up that the first cycle did not remove but the second cycle got it.  Don't know for sure just glad it's working!

Posted on Nov 17, 2008

  • 718 Answers

SOURCE: switch and capacitor crapped out on 1/2 hp Sears bench grinder

Replacement should be simple. Just do a one for one hookup with the new part, after you unplug it first.
For a diagram go to;

http://www.searspartsdirect.com/partsdirect/getSubComp.pd?modelNumber=397.1949&productCategoryId=0721000&brandId=0247&modelName=CRAFTSMAN-1%2F2-H.P.-GRINDER&diagramPageId=00001&documentId=00023041&pop=flush

Posted on Mar 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mass airflow sensor


Look up both years on a site like Rock Auto,
or ask an auto parts store or dealer to cross
the two years to see if it fits both

Jul 17, 2013 | Suzuki Aerio Cars & Trucks

1 Answer

Expobar steam wand loss of pressure


Are you leaving enough time for the water to heat up to a sufficient temperature? Typically 20 minutes is needed to ensure good steam flow.

May 25, 2012 | EXPOBAR Office Control Espresso Machine

1 Answer

The auto wash/start/delay start touch controls will not respond...all other control panel area's are working, but I can not get it to start.


It is possible the button contact has moisture or some contaminent. Best to open the control panel and check under the button. Take photos as you go along to make sure it all fits together. You can check the part locations in this diagram.

Feb 11, 2011 | Maytag 24 in. MDBH955AW Built-in...

1 Answer

Safety valve cn10 keeps activating about 10 seconds after switch on. any ideas anyone. stafco markus 2 group semi auto


Try this open the steam wand and leave on when turning the machine on, when valve stats hissing with steam close. If that works then the vent valve needs to be replaced, If it blows out hot steam from valve then the pressure stat is not operating properly.

Jun 22, 2010 | EXPOBAR Office Control Espresso Machine

1 Answer

I need a Push-button Panel With Tea-program for


Check with espresssoparts.com. They carry a wide assortment of parts.

Oct 26, 2009 | EXPOBAR Office Control Espresso Machine

1 Answer

Sreen shrunk a bit and now cant chanage it to normal


Control Panel->System->Hardware->Device Manager. Select Display Adapters and uninstall it. Then Ask Windows to scan for new HW. Let it detect and install the display adapter. If this does not work then select Monitor and uninstall it. Make Windows detect the monitor and install it.

Aug 23, 2009 | Hannspree HANNS-G 19" Widescreen Monitor

1 Answer

Need to program stafco markus 2 group espresso machine


Normal you hold in the continuous flow button till all lights flash or stay on.
then you press the first button to program, once the right amount of coffee has come out press that button again.

Continue this with all buttons.

Please sign up to servicing program, we teach you how to service and maintain your machine. This will save you $$$ hundreds in service agent fees. We stock all parts.
Email me at sales@willisjococoffee.com.au

Apr 30, 2009 | Nuova Simonelli Program VIP Coffee Maker,...

Not finding what you are looking for?
Coffee Makers & Espresso Machines Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top EXPOBAR Coffee Makers & Espresso Machines Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Kolbrun...

Level 3 Expert

1205 Answers

kakima

Level 3 Expert

102366 Answers

Are you an EXPOBAR Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...