Question about Villeroy & Boch Villeroy-Boch BA200BEL2MHV

Open Question

Jacuzzi bath not turning on

My jacuzzi bath is not turning on, the green light shows when water level is high enough, we have a new control and new batteries. how do I fix

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Push button on my jacuzzi won't start it despite power going to unit


The air button on your tub may be bad and not sending enough air to the air switch located on the bath pump.
The way to check this is to remove the bath pump and see if you can turn the bath pump on by taking a large straw and blowing into the air switch on the bath pump to see if you can get the bath pump to turn on.
If the bath pump comes on then you know you have a bad air button.
If you cannot get the bath pump to turn on then remove the air switch and plug the two wires going to the air switch together and then plugging the pump into a power outlet you know has power.
If the bath pump comes on then you know you need a new air switch in the motor.
If the motor does not come on then you need a new bath pump.


Rod
US Parts Center
888-521-6183

Mar 10, 2013 | Whirlpool 5' Jacuzzi Tub Bathtub Cetra...

1 Answer

Can't get enough water in toilet bowl to flush the waste


Adjust your tower to let the bowl fill up more.....google your problem if you dont understand...depends on what kind of tower you have....should have teeth on the tower itself to make it fill more...try pulling up on the float...

Mar 15, 2012 | Jacuzzi Bath Perfecta EZ33 959 White round...

1 Answer

The water level in tank is low. How do you adjust?


There's no certain way for me to know which fill valve you have in there, but locate the float. This floats on the water level and turns off the water when the tank is full. There's probably a screw on the float arm that lets you adjust the float up and down, adjusting the full water level. You may be able to loosen a collar on the bottom of the fill assembly and slide the whole thing up and down (make sure you turn off the water valve when you do this because the whole thing can pull apart), or you may be able to simply turn the entire fill assembly which will raise and lower it if it's built that way. Make sure the new water level doesn't go above the level of the refill tube or the water will go down the tube and the valve will never turn off.

Jul 12, 2010 | Jacuzzi Bath Perfecta EZ33 959 White round...

1 Answer

Bowel cleaning


Check the ports under the rim and make sure they are not clogged. To do this you can use a nail or pin to clean them out.
Right under the rim of the bowl are these ports that allow the water to flow into bowl in a turning motion to aid in flushing and cleaning wall's of the bowl.
Inside the tank check the fill tube and make sure it is connected from the fill valve to the over flow tube. Also check the fill level in the tank and make sure water is up to the line on the fill tube about 5/8" from top of tube.

Jun 06, 2010 | Jacuzzi Bath Perfecta EZ33 959 White round...

2 Answers

Tank not holding fill level...


Most likely, you do not have a good seal on the flapper valve at the bottom of the tank. To confirm, try this:
Turn off water and flush toilet. Then lift up the flapper valve and put a light coating of vaseline on the mating surface where it contacts the toilet tank when closed.
Turn water back on and see if it continues misbehaving. If that fixes it, it was a bad seal. Usually that is all it takes.

Dec 15, 2009 | Jacuzzi Bath Perfecta EZ33 959 White round...

1 Answer

Water level drops in bowl after it fills


If very little water is used on initial flush, The bowl is functioning as a tank for second thorough flush. The high water level cannot stay high in the bowl while in motion or you would have a mess ion start and stops.

May 28, 2009 | Jacuzzi Bath Perfecta EZ33 959 White round...

2 Answers

"Jacuzzi j-400 series" hot tub- F1 code flashes on control panel


Your circulation pump isn't working you should see the flow awitch closing if you have the visible model and hear the pump running.. If its the smaller circulation pump model it needs replacing

May 18, 2009 | Jacuzzi Bath Nova H530 917 Black Soaking...

1 Answer

Is there a manual. The water keeps running.


the fill valve shut off level setting is too high. water in the tank is overflowing in the overflow tube. adjust fill valve to shut off at lower tank level

May 12, 2009 | Jacuzzi Bath Era BK37 959 White toilet...

1 Answer

Do I have to clean my jacuzzi every day?


Just clean it once a week is fine.

Please rate!

Mar 17, 2009 | Whirlpool Home

Not finding what you are looking for?
Villeroy & Boch Villeroy-Boch BA200BEL2MHV Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Villeroy & Boch Home Experts

J.D. Browning
J.D. Browning

Level 3 Expert

2760 Answers

kakima

Level 3 Expert

102366 Answers

Lisa Zhuo
Lisa Zhuo

Level 1 Expert

7 Answers

Are you a Villeroy & Boch Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...