Plu 1-4 keys not functioning

if it still has a program and the battery is not dead, power off/on with switch on right with key in sm. To just reset the whole thing to factory condition so you can resell it press down check button (3rd up from bottom<csh> key on right while powering off and on again in the sm position. THEN press top left button, then bottom left button, then top right button and finally bottom right button on keyboard

PartsandTheirFunctions Printer cover Operator display Keyboard Drawer Check slot Drawer lock SD card slot (Refer to the "SD CARD Mode" section.) Printer The printer is a thermal printer, and therefore it does not require any type of ink ribbon or cartridge. The average life of the printer is approximately 6 million lines. When removing the printer cover, lift up its rear. When installing the printer cover, hook it on the pawls on the cabinet and shut it. CAUTION:Thepapercutterismountedontheprintercover.Becarefulnottocutyourself. Keyboard ? Keyboardlayout ? Functionkeylist { Receipt paper feed key PLU/sub-department/UPC key } Journal paper feed key Department code entry key Function menu key Department shift key a Auto key CLK# Clerk code entry key w Tax1 shift key Department 1-40 key 0 Percent 1 key FI Cursor (up/down arrow) key - Discount key m Mode key t Void key Escape/Cancel key H Help key X Charge 1 key f Refund key R Receipt print key @ Multiplication key Y Charge 2 key P Decimal point key u PLU/UPC inquiry key l Clear key x Check key 0 9 : Numeric key ; Non-add code/Time display/Subtotal key A Cash/Amount tender/No sale key Displays ? Operatordisplay •Screenexample1(REGmode) Salesinformationarea: When a transaction information occupies more than 2 lines, you can scroll to the direction by using the F I keys. Sales information you have just entered such as items and prices will appear between 1st line and 2nd line. Total is always appear at 3rd line. NumericEntryArea: Statusarea: Mode name Status information Clerk code Receipt ON/OFF status indicator (R) : Appears when the receipt ON-OFF function signs OFF. Sentinel mark (X) : Appears when the cash in drawer exceeds a programmed sentinel amount. The sentinel check is performed for the total cash in drawer.

try to do an 'initial clear'
turn power switch on right side of reg to OFF pos
turn control lock to P position
press and hold SBTL key and turn power switch to ON pos
should print 'Initial clear ok'
might need to repeat a couple of times

48 is the code for the PLU button, not a flat PLU. they are different.
To set a flat PLU, Turn key to program 4 subtotal Type the PLU number to be assigned using the numeric keys Type 063 Press the flat PLU location to save the PLU number there Press SUBTOTAL
If you get an error when you press the location, then you already have an amount in the totaliser (end of day report) for that location and you will need to do a PLU report and possibly a department report in both Z1 and Z2 modes to clear the totals of that function before you can allocate it. Let me know if you get an error and I'll help you through. Good to see that you have almost removed all of the old programming

Ok. it looks like you have a dept or item assigned in place of your PLU button. You just need to replace it with the original and then you can try linking the depts again.
Turn key to program mode 4 SUBTOTAL 48 Now press the PLU button SUBTOTAL
Now try the programming for department link again and see if it works this time.
It sounds like you don't have the programming manual. you should have two manuals if you are programming the machine yourself. There is no programming in the user manual except for quick setups so it is for operating only. You should have this manual as well for the programming: http://the-checkout-tech.com/manuals/cashregisters/Casio_TE-2200_and_TE-2400_dealers_manual.html
If you look at the preview, you will see that this manual has all the system programming in it. I assumed you had it when you were mentioning the VAT breakdown programming. It is pretty much essential for anything you want to program in future so I recommend you grab it and have a look at the table that I mentioned for transaction key programming on the CASH button

You need to check that your PLU button really is a PLU button for a start. In REG mode, press 1 then the PLU button. It should register the product that is also on your first item button. If you press 2 then PLU, it should register the second product on your keyboard. If it doesn't then the PLU button has been moved from the original location. I can give you the code to replace it.
To set the NO SALE button back to location, Turn key to Program mode, 4 SUBTOTAL 41 Now press the NO SALE button on your keyboard. SUBTOTAL Now turn the key back to REG and try the NO SALE button. If it still does nothing then you probably have special programming to disallow the NO SALE command. Let me know.
There is a setting for VAT breakdown printing in the table under the heading 'TRANSACTION KEY PROGRAM' Find this in your manual and under it you will see a table with the heading <CASH>,<CHARGE>,<CHECK>. Near the bottom of the table is the breakdown setting. I assume you are familiar with this programming as you said you had tried other VAT settings. If you just want this setting turned on, use 100000 when programming. Otherwise, you will need to create a number depending upon what features you want to enable for each payment button.

Hi. The previous owner just had PLUs linked to the depts that suited them. to link PLUs to depts,
Turn key to Program mode.
3 SUBTOTAL
1166 SUBTOTAL
Now type the PLU number you want to link. E.g if you want to link PLU 6, then press 6 on the number pad (don't press the actual PLU, just type its number on the number pad)
Now press the button marked PLU. It should be near the other function buttons.
Now type the department number to link to. Use two digits. E.g to link to dept 5, type 05 on the number pad.
Press CASH
Press SUBTOTAL
As for NO SALE button, does it actually show the command NO SALE, or NS on the display when you press it? It may have been removed from the keyboard. Does the drawer open when you finish a sale normally?
There is normally a setting in key features for VAT breakdown on the CASH button. Make sure this is set so that it prints the breakdown. Add on means you sell at a tax exclusive price and the tax is added on to that by the register. Add in means you sell at a tax inclusive price and want the register to show how much of it was tax.
Hope this helps. See how you get on.
------------------------------------------------------------------------
If anyone needs a Casio TE2200 or TE-2400 manual, try here: http://the-checkout-tech.com/manuals/cashregisters/Casio4.php

Ok, the first issue is the oven temp sensor. it is shorted. you will need to replace this device asap. Now, the second is is concerning the Self clean latch. it is not functioning and it is unable to be locked by the control(shorted). Use the procedure below to test this device.



1. If door latched:

1. Disconnect power from unit.
2. Check wires and connectors from control to door switch, then from door switch to control. If no damage to wires and all connectors okay, proceed to step C.
3. Replace door switch.
4. Re-apply power.
5. Press and hold any key down for 1 minute to clear F5 failure code from memory. F2 will appear. Press CANCEL and observe for 1 minute to ensure operation is correct.

2. If door not latched:

1. Disconnect power from unit.
2. Check wires and connectors from control to latch switch, then from latch switch to control. If no damage to wires and all connectors okay, proceed to step C.
3. Repeat steps A and B for door switch.

3. Measure door switch (door open = switch open small low voltage terminals). Replace switch if defective.
4. Measure latch switch (unlatch = switch open, CAUTION - oven light contacts are closed). Replace switch if defective.
5. If corrections are made in any step, reconnect power to control. Press and hold any key for 1 minute to clear R failure code from memory. F2 will appear. Press CANCEL and observe for 1 minute to ensure operation is correct.
6. If failure remains, disconnect power and replace control.

Hi.
I haven't worked with the 1550, but most Casios are the same.
Try this:

Turn key to program.
Press 0
Press the PLU that you want to set as open priced.
Press SUBTOTAL

That will set the price as 0 for that PLU. Now we set the feature for that PLU to allow manual pricing.

Leave key on program.
3
SUBTOATL
0
Press the PLU again
SUBTOTAL

Try that. If you had tax set to that PLU, you may need to set it again.

Mark

Try these steps to cancel the error, press the buttons continously

STEP1. Press CLEAR key then EXPOSURE key then CLEAR key then EXPOSURE key

STEP2. Then you are inside the simulation if the display turns OFF if not, do again step 1 until the display turns off.

STEP3.press 14 then press print button