Question about Whirlpool 3.6 cu. ft. Cabrio H2Low Wash System with Auto Load Sensing Top Load Washer"

Open Question

Tub Drip after wash is completed

Steady drip into tub when cycles are done

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Joe Onley
  • 363 Answers

SOURCE: dripping water into tub

seems to me that there is something holding open the valves. you can take the hoses off the back (turn off the water first, naturally) and see if there is a lot of buildup inside the valves. There are screens in there that you could take out to inspect inside the valve from that side, perhaps you can see something there holding it open. If there is nothing you can do, you may have to replace the valves. Not sure of cost but shouldn't be too costly.

Posted on Sep 01, 2009

Ad
bozcro
  • 867 Answers

SOURCE: Drips from center of front cover when filling at 3-4 inches

after carefully reading this, the leak is at the machines water valves, or from them to hose to tub.

Posted on Sep 10, 2009

honeymokey
  • 3113 Answers

SOURCE: why does my ultimate care

You need to replace the water valve

Posted on Mar 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My washer will drip water back in the tub after complete washing is finished Why Help


If the water is dripping in from the area where it normally fills for a wash cycle, then you probably have a problem with the water valve. You can open them up to see if debris has made its way into the valve, but they normally are not real expensive and it may just be easier and less hassle to just replace the entire valve. Hope this helps!

Feb 18, 2015 | Maytag Washing Machines

2 Answers

Water leaks (drips ) into tub after cycle/spin is complete


You have a bad pressure switch or the small hose connecting to the pressure switch may be bad

If the washer leaks water when is filling only, check the following: 1.Fill hoses
2.The water mixing valve

3.Filling injector ( If your washer uses one )
4.Filling spout


If the washing machine leaks during the wash cycle, check the following:
1.The pump
2.The tub stem & seal
3.Tub to pump hose
4.The drain hose
5.Tub (rusted holes)
6.The drum support bolts


If the washing machine leaks during the spin cycle, check the following:
1.The drain hose
2.The tub cover seal
3.The pump
4.The pump hoses

5.The stem & seal
6.The drum support bolts

Feb 10, 2008 | Maytag LAT2300 Top Load Washer

1 Answer

I have an MAV7600 Maytag washer the hot water fill valve drip after the cycle complates


if the washer keeps taking water and even when the washer is on the off position.
The problem could be a bad water valve.

Mar 15, 2012 | Maytag MAV7600 Top Load Washer

1 Answer

Water continues to drip into the tub even after all cycles have completed. my tub is filling up with water, I have turned off the water to the machine but it continues.


The water inlet valve needs to be replaced. It's not shutting off the water completely. It's located where the water hoses connect to the washer.

Oct 09, 2010 | Maytag Washing Machines

1 Answer

After wash cycle is finished I lift the tub lid and water is dripping into tub.


You may be looking at residual water dripping down from the rim. If the drip is located near where the water fills from, then you may have a water valve (could be either hot or cold side) that is not able to close completely. The valves are typically replaced, but sometimes cleaning can help for short term. Consult your user manual for removal / replacement instructions.

Aug 18, 2010 | Maytag Washing Machines

1 Answer

Drips from center of front cover when filling at 3-4 inches


after carefully reading this, the leak is at the machines water valves, or from them to hose to tub.

Sep 10, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

GE WHDSR315 washer randomly drips still after done filling


you looking for a new water valve assembly...not very hard to replace..maybe a lil' messy

Aug 28, 2009 | Washing Machines

1 Answer

Leak


Your inlet water valve where the fill hoses attach is stuck open.

Mar 18, 2009 | Washing Machines

1 Answer

Washer continues to drip into tub after cycle in complete.


contstant water dripping into tub sounds like a bad water valve, no repairing valve just replace it

Feb 25, 2008 | Maytag Atlantis MAV6000 Top Load Washer

Not finding what you are looking for?
Whirlpool 3.6 cu. ft. Cabrio H2Low Wash System with Auto Load Sensing Top Load Washer" Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal DeAngelo

Level 3 Expert

2328 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...