Question about C3RS730 LCD (C3RS730LCD) 2way 4Channel Vehicle Security Syste

1 Answer

Autopage XT-1100 Here is a question, how do I program the XT-1100 key fob to alert me when the alarm is triggered on my vehicle??

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Try to search for Autopage XT-1100 Manual. im sure you will be able to find the functions there

Posted on Apr 02, 2014

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 7 Answers

SOURCE: i have the normal alarm Autopage AutoPage C3RS603

Nothing is hard to hookup just time consuming andf it all depends on how good you R with wiring how good R you..?

Posted on Jul 16, 2010

  • 139 Answers

SOURCE: i need the manual to

The Autopage XT-42LCD is used to operate two systems, the RF-420LCD and RS-622. Since you state that you need to activate a remote start that narrows it down to the RS-622. You can download the manual for this unit at the following link:

http://www.autopageusa.com/resources/RS622operationManual.pdf

Posted on Jan 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My youkon alarm goes off every time i unlock the door with the autopage key fob.


Aftermarket alarms have to be configured to bypass the factory alarm system when using it.
I don't mean you have to permanently delete your factory alarm. What I am saying is, when you use your autopage key fob to unlock your doors, it must also send a signal to the disarm wire of your factory system simultaneously. If not, your alarm will go off just like you are experiencing.

May 16, 2017 | GMC Yukon Cars & Trucks

1 Answer

Xt 33 autopage (crank) but no start


could be your car requires a bypass module... or the safety inputs preventing the alarm from starting car are in place... without knowing your make/model that's the best I can do...

Jul 18, 2016 | Autopage Vehicle Parts & Accessories

1 Answer

How do I reserve battery life on my autopage alarm key pad model XT-73LCD


If you put remote in your pocket or your purse make sure it doesn't push on any buttons!

Mar 30, 2014 | C3RS915 SST Remote Car Start Vehicle...

1 Answer

RS855LCD 2-way remote and key fob dreain batteries


I see this is a old post but, I have this unit in a used van that came with no remotes. A local audio shop paired it up with a AUTOPAGE XT-33. I can lock,unlock,start with this remote. Just remember to keep the drivers open while doing these steps.
1. Turn the Ignition 'switch 'OFF/ON' 3 TIMES and stay in
ON position. Within 15 seconds.
2. Push the Valet switch 2 times and hold in on the2ndpush, when a long chirp is heard then release the valet
switch. You are now in the Transmitter programming mode.
Program:1. Press the Lock button on transmitter 1 until the siren
responds on Car with a confirming chirp; the first
transmitter is now programmed to Car.
Exit: Turn Ignition to 'OFF' position, or leave it for 15
seconds. 3 long chirps will confirm exit.
Note: If more than 4 transmitters programmed, the system
will only keep the last four.
The Valet switch is a little Red Push Button that should be
mounted under the lower left side of you dash or in the lower
left kick panel near the E-brake pedal.

Jan 14, 2012 | RS855LCD AutoPage MultiChannel 2 Way...

1 Answer

Why does the alarm in my car go off when I try to start it with the remote car starter?


If this is the vehicle's factory alarm that is being triggered then your factory alarm must be disarmed prior to the remote starter sequence. The Autopage unit has a factory disarm wire available for this purpose. When the alarm triggers again try turning the key in the driver's door to see if there is a factory disarm wire available in the vehicle or if the factory alarm is RF disarm only. If it is the after market alarm that is being triggered then you made need to decrease the sensitivity.

Nov 23, 2010 | C3RS727LCD 4Channel Alarm with Remote Car...

Not finding what you are looking for?
C3RS730 LCD (C3RS730LCD) 2way 4Channel Vehicle Security Syste Logo

Related Topics:

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Autopage Vehicle Parts & Accessories Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

John
John

Level 2 Expert

509 Answers

Charles Osborn

Level 2 Expert

71 Answers

Are you an Autopage Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...