Question about Exercise & Fitness

Open Question

Ee error list init star trac treadmill

Hello: someone could please help me with the problem of my treadmill star trac model pro (ee error list init)

Posted by on

3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: StarTrac Pro Treadmill startup error (ee error

StarTrac Pro Treadmill startup error

Posted on Jul 05, 2010

  • 1196 Answers

SOURCE: how do i reset ee error list init on startrac pro


I will advice you try re-calibrate your treadmill, follow the procedure below to re-calibrate it,

Step 1 Stand on the side rails of the treadmill for safety purposes. Remove the safety key. Step 2 Press and hold the two incline buttons. The incline buttons are blue and on the left side of the display. Hold the up and down button simultaneously. Release the buttons when the display reads "Calibration."
Step 3 Press the green start button located either above or below the large, red stop button (depending on your model). Stay on the side rails as the treadmill belt begins to move. Both the speed and incline should go through their full range from lowest to highest, and then back down again.
Step 4 Repeat the process if the display does not read "Calibration Successful.

Posted on Sep 22, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Take apart star trac pro treadmill

Replacement Parts for Fitness Exercise Equipment at SPORTSMITH

You can use the link below, combined with your model and serial number, to find the parts diagram. This should aid in taking apart your treadmill.

StarTrac Treadmill Repair Parts Belts Decks Rollers SPORTSMITH net

Oct 15, 2015 | Star trac Exercise & Fitness

1 Answer

Fault on treadmill saying E1 been told its batteries were are they situated on machine

Here is a link to the manual.

You might want to try the troubleshooting procedures on pg 47.

States if error code appears, "Call your dealer or Star Trac at (800) 503-1221, or USA 1-714-669-1660 for service."

Mar 02, 2015 | Startrac Fitness Products Star Trac Pro S...

1 Answer

My star trac treadmill is reading key dv

I think you mean key dn....This means you have a stuck key on your keypad. See page 55 of the service manual.

Jan 13, 2014 | Startrac Fitness Products Star Trac Pro S...

1 Answer

Trac Star 4500 trouble Code EL STL

The error code by definition is listed in section 3 of the service manual.

Dec 08, 2013 | Startrac Fitness Products Star Trac 4500...

1 Answer

Ee error list init

It' s full sheet .You can start with reloading the software with Fisps
You will need to Load Primary 8.10 and Secondary 3.30
Software and instructions can be found at:
If this does not work it will require a complete new display electronics:

May 09, 2013 | Startrac Fitness Products Star Trac Pro S...

1 Answer

I have star trac pro treadmill,when i shifted from another place it show the error

1) Run the software calibration for diagnose, troubleshooting.
2) However adjust the reed switch, clean, and tight any wires connector see the diagram
3) adjust the speed sensor, clean, and tigh the wires connector see the diagram attached.

Jul 06, 2012 | Startrac Fitness Products Star Trac Pro S...

1 Answer

Power supply ok but it's error coming check speed system

Dear Sir:
Please run the software calibration for easy diagnose and troubleshooting and fixing. Clean very well the speed sensor, and tight the connector.

sincerely. God bless you

Apr 16, 2012 | Startrac Fitness Products Star Trac Pro S...

1 Answer

My treadmill will start and you can increase speed and incline but fan will not work and you can not decrease speed or incline. And I can not stop the treadmill. I have to emer. stop.

I'm not sure if this will help.

First I was unable to identiy your model. Star Trac makes 'S Series' treadmills and Pro Tread DC (5500 Pro S model) treadmills. Can you be more specific on your model?

Second. I have used Star Trac customer service in the past and they are the best. They are responsive, and knowledgeable, and will provide troubleshooting flowcharts to help you solve your problem. I highly recommend giving them a call.

Hope this helps,

Jan 21, 2011 | Startrac Fitness Products Star Trac Pro S...

1 Answer

Looking for circuit board stratrac pro


If you are looking to but one, you can go to, and enter your part number or the model number and order it.

Hope this helps you, Matt

Dec 05, 2010 | Startrac Fitness Products Star Trac Pro S...

Not finding what you are looking for?
Exercise & Fitness Logo

Related Topics:

216 people viewed this question

Ask a Question

Usually answered in minutes!

Top Exercise & Fitness Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Sportsmith LLC
Sportsmith LLC

Level 3 Expert

914 Answers

Tom Chichester

Level 3 Expert

34204 Answers

Are you an Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides