Question about Kenmore Elite HE4 Electric Dryer

Open Question

Front load dryer plastic window cracked on dryer door

Need to know how to remove cracked plastic window part door on dryer door to replace it with a new one. The new piece I recieved is just looks like a plastic round tinted window that looks like it fits right into the dryer door but I cant figure out how to remove the old one thats on the dryer door now??

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
jsrock516
  • 5911 Answers

SOURCE: window dryer

Okay...thank you for the feedback. This repair will be much easier if you remove the door from the dryer. Just loosen the screws on the hinge where it connects to the dryer door opening. That is...remove the door with the hinge still attached. CAUTION: Make sure you support the weight of the door as you loosen or tighten the door hinge. Lay the door face down on a soft surface like some towels. Locate the screws on the door interior. There are a series of them that go around the perimeter of the door. Removing these screws will enable you to disassemble the entire door. The interior door facing will come off, allowing access to all the remaining parts. Just make sure you remember how they come apart. If you get confused, you can go to searspartsdirect.com. Type in your model number and locate the "Door Parts" heading on the next page. There should be an illustration on how the door is assembled. I hope this helps you. If you need further assistance, please post back and let me know.

Posted on May 24, 2008

Ad
  • 1 Answer

SOURCE: I DONT KNOW HOW TO REMOVE THE OLD LATCH FROM MY

after making sure i had the right replacement part, i pulled the old latch out of the door with pliers 'and a small screwdriver. once out I pushed the new latch right in and it works great. took less than 5 minutes.

Posted on Apr 01, 2009

  • 32 Answers

SOURCE: There is a plastic oval piece that fits between

Most frigidaire dryers have front felt seals with nylon slides on top that the front of the drum rides on. Without M# can't be sure if yours is like this.

Posted on Dec 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cracked plastic window in front loader washer


Stop Kicking Your Washer!!! First! The glass is a material Hybrid from the NASA Apollo Space Program! That was Some Kick! Can't buy Just the Laminar Plastic Piece. You have to purchase THE ENTIRE DOOR dummy! Go to Sears.com, They will Love your Money and deliver via Space Shuttle Free...LOL

Oct 13, 2013 | LG WM2688HWM TROMM SteamWasher

1 Answer

Kenmore electric dryer series 70, on the inside of my dryer there is a plastic white ring that is cracked and brittle, clothes get stuck on this ring and tear, can I replace this white ring?


Yes, you can replace that ring.
I believe you have a front loading machine, if so then you will need to remove the front of the machine to expose the ring, drum and belt.
Try this website and see if they can supply the part you need.
Good luck, I hope this helped

http://www.partsselect.com/

Oct 03, 2009 | Kenmore 73952 Gas Dryer

1 Answer

My Kenmore HE dryer door handle has cracked. How


Carefully remove the door from the dryer by removing the screws from the hinges and lie on a flat surface face down. Lay a towel under the door to prevent scratching the door window. Remove the screws from the back of the dryer door and the hinge. The back panel should lift off exposing the screws holding the handle in place.

Searspartsdirect.com has some excellent exploded view diagrams that you can work from as well.

If you have questions, please let me know. I hope this helps you.

Sep 30, 2009 | Kenmore Elite HE4 Electric Dryer

1 Answer

NVLR333ETOWB HOTPOINT DRYER EATING CLOTHES


I have the same dryer doing the same thing. Open the door and take the two screws out and lift the top. Remove the two screws that hold the front on. Remove the front. On mine both the plastic parts that stay on the front when it is removed are cracked and needing replaced. I found over 20 buttons that the dryer had pulled off clothes stuck in the front door. I'm sure if it will be cost effective to buy both these parts or not.

Jan 13, 2009 | GE DBXR453EV Dryer

1 Answer

Front door plastic face plate of washer HE3t


yes. there aretorque screws around the inside frame remoive them and the 2 pieces will seperate. you can replace it then. be carefull if you remove the screws from the hinge the whole door will fall off. only six or so screws need to be removed

Jan 04, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

Window dryer


Okay...thank you for the feedback. This repair will be much easier if you remove the door from the dryer. Just loosen the screws on the hinge where it connects to the dryer door opening. That is...remove the door with the hinge still attached. CAUTION: Make sure you support the weight of the door as you loosen or tighten the door hinge. Lay the door face down on a soft surface like some towels. Locate the screws on the door interior. There are a series of them that go around the perimeter of the door. Removing these screws will enable you to disassemble the entire door. The interior door facing will come off, allowing access to all the remaining parts. Just make sure you remember how they come apart. If you get confused, you can go to searspartsdirect.com. Type in your model number and locate the "Door Parts" heading on the next page. There should be an illustration on how the door is assembled. I hope this helps you. If you need further assistance, please post back and let me know.

May 24, 2008 | Kenmore Elite HE4 Electric Dryer

1 Answer

Bosch dryer nexxt 500 (wtmc3521uc) broker plastic window


The plastic window can be repalced you dont need to get a new door...

Just remove the door from the washing machine and undue the screws around the rim and unclp the plastic rim and you should be able to fit in a new one with no problem...

hope it helps any questions dont hesitate to ask..

Jan 20, 2008 | Bosch WFMC 3200 Front Load Washer

Not finding what you are looking for?
Kenmore Elite HE4 Electric Dryer Logo

Related Topics:

225 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal DeAngelo

Level 3 Expert

2509 Answers

Tim Whalen

Level 3 Expert

3074 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...