Question about Kenmore Washing Machines

1 Answer

Front loader door unlocks during cycles with door lock light on.

Kenmore model 417.29052990
At certain times when the machine is operating, the door will unlock, causing the door switch to open, stopping the machine. The door remains closed, but not as tight as when the door lock is engaged. The door lock light is on, and stays on constant during machine operation.
I can resume the cycle by pressing on the door to close the door switch, then I must hold the door closed tight until I hear the door lock engage and lock the door again. Then I wait until the next unlock condition.
This appears to occur at the same time during each operation.
Any suggestions? Thanks.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

It appears your timer/main controller/CCU has failed in this instance.

For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.
I recommend both sites because ...


FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.

PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.


If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.


Anything too complicated or beyond your scope should be handled by a professional.

If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.




Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Posted on Sep 17, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My washer works but it will not work in the spin cycle


Every washing machine, top or front loader, has a safety feature that disables the spin functions and that is the lid switch/lock for top loaders and door switch/lock assembly for front loaders. This is to prevent injury when the lid/door is opened during a high speed spin. Check lid/door switch harness and connections. Replace lid/door switch assembly if no issue found with the harness and connections.

Sep 30, 2010 | Kenmore Washing Machines

1 Answer

Whirlpool duet washer GHW9300PW4 .... The control lock is on .. I did get door to open, It will not shut off and none of the cycles will light up or start.. Please help..


This advise is for Kenmore Elite and Whirlpool Duet front loader washers and dryers with a Control Lock problem.

This may or may not be an indication of a serious problem. In the majority of the cases, this is a simple operator error. Nearly all these model appliances have some sort of Control Lock feature on the front panel now. This is a designed safety feature that is used to prevent small children from manipulating the controls. The controls can be easily locked or unlocked by pressing and holding the following button on the front panel:

Whirlpool Duet Washer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Whirlpool Duet Dryer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Kenmore Elite Washer - Press and hold the DRAIN/SPIN button for 3 seconds.

Kenmore Elite Dryer - Press and hold the AUTO DRY LEVEL button for 3 seconds.

These instructions may not be all inclusive for all Kenmore and Whirlpool models, but they are the most common. Chances are, if you have a Control Lock feature, the instructions will be printed on the front panel adjacent to the button that is required to lock or unlock the controls.

NOTE: These instructions may also work for newer model Maytag, Hotpoint, Admiral and Fridgidaire model front loaders as well. Refer to your owner's manual or front panel for instructions pertaining to your sepcific model.

If the Control Lock feature will not lock or unlock the appliance, unplugging the unit for AT LEAST 30 minutes is recommended in order to reset the main control board. In many cases this is all that is required to correct momentary glitches.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Aug 19, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

My whirlpool duet 2004 front load washers door is locked, time is flashing and pump is on. Unable to stop or open door. tried to unplug. Control lock is not on. My wife tried to add clothes when the add a...


This advise is for Kenmore Elite and Whirlpool Duet front loader washers and dryers with a Control Lock problem.

This may or may not be an indication of a serious problem. In the majority of the cases, this is a simple operator error. Nearly all these model appliances have some sort of Control Lock feature on the front panel now. This is a designed safety feature that is used to prevent small children from manipulating the controls. The controls can be easily locked or unlocked by pressing and holding the following button on the front panel:

Whirlpool Duet Washer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Whirlpool Duet Dryer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Kenmore Elite Washer - Press and hold the DRAIN/SPIN button for 3 seconds.

Kenmore Elite Dryer - Press and hold the AUTO DRY LEVEL button for 3 seconds.

These instructions may not be all inclusive for all Kenmore and Whirlpool models, but they are the most common. Chances are, if you have a Control Lock feature, the instructions will be printed on the front panel adjacent to the button that is required to lock or unlock the controls.

NOTE: These instructions may also work for newer model Maytag, Hotpoint, Admiral and Fridgidaire model front loaders as well. Refer to your owner's manual or front panel for instructions pertaining to your sepcific model.

If the Control Lock feature will not lock or unlock the appliance, unplugging the unit for AT LEAST 30 minutes is recommended in order to reset the main control board. In many cases this is all that is required to correct momentary glitches.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 08, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Kenmore HE4T Front loader control lock indicator light is on and will not let me use any other controls.


This advise is for Kenmore Elite and Whirlpool Duet front loader washers and dryers with a Control Lock problem.

This may or may not be an indication of a serious problem. In the majority of the cases, this is a simple operator error. Nearly all these model appliances have some sort of Control Lock feature on the front panel now. This is a designed safety feature that is used to prevent small children from manipulating the controls. The controls can be easily locked or unlocked by pressing and holding the following button on the front panel:

Whirlpool Duet Washer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Whirlpool Duet Dryer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Kenmore Elite Washer - Press and hold the DRAIN/SPIN button for 3 seconds.

Kenmore Elite Dryer - Press and hold the AUTO DRY LEVEL button for 3 seconds.

These instructions may not be all inclusive for all Kenmore and Whirlpool models, but they are the most common. Chances are, if you have a Control Lock feature, the instructions will be printed on the front panel adjacent to the button that is required to lock or unlock the controls.

NOTE: These instructions may also work for newer model Maytag, Hotpoint, Admiral and Fridgidaire model front loaders as well. Refer to your owner's manual or front panel for instructions pertaining to your sepcific model.

If the Control Lock feature will not lock or unlock the appliance, unplugging the unit for AT LEAST 30 minutes is recommended in order to reset the main control board. In many cases this is all that is required to correct momentary glitches.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 05, 2009 | Kenmore Washing Machines

1 Answer

Light on reads control panel locked - how do I unlock it?


This advise is for Kenmore Elite and Whirlpool Duet front loader washers and dryers with a Control Lock problem.

This may or may not be an indication of a serious problem. In the majority of the cases, this is a simple operator error. Nearly all these model appliances have some sort of Control Lock feature on the front panel now. This is a designed safety feature that is used to prevent small children from manipulating the controls. The controls can be easily locked or unlocked by pressing and holding the following button on the front panel:

Whirlpool Duet Washer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Whirlpool Duet Dryer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Kenmore Elite Washer - Press and hold the DRAIN/SPIN button for 3 seconds.

Kenmore Elite Dryer - Press and hold the AUTO DRY LEVEL button for 3 seconds.

These instructions may not be all inclusive for all Kenmore and Whirlpool models, but they are the most common. Chances are, if you have a Control Lock feature, the instructions will be printed on the front panel adjacent to the button that is required to lock or unlock the controls.

NOTE: These instructions may also work for newer model Maytag, Hotpoint, Admiral and Fridgidaire model front loaders as well. Refer to your owner's manual or front panel for instructions pertaining to your sepcific model.

If the Control Lock feature will not lock or unlock the appliance, unplugging the unit for AT LEAST 30 minutes is recommended in order to reset the main control board. In many cases this is all that is required to correct momentary glitches.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Jun 27, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

Kenmore front loader Model 48102 will not start


This advise is for Kenmore Elite and Whirlpool Duet front loader washers and dryers with a Control Lock problem.

This may or may not be an indication of a serious problem. In the majority of the cases, this is a simple operator error. Nearly all these model appliances have some sort of Control Lock feature on the front panel now. This is a designed safety feature that is used to prevent small children from manipulating the controls. The controls can be easily locked or unlocked by pressing and holding the following button on the front panel:

Whirlpool Duet Washer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Whirlpool Duet Dryer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Kenmore Elite Washer - Press and hold the DRAIN/SPIN button for 3 seconds.

Kenmore Elite Dryer - Press and hold the AUTO DRY LEVEL button for 3 seconds.

These instructions may not be all inclusive for all Kenmore and Whirlpool models, but they are the most common. Chances are, if you have a Control Lock feature, the instructions will be printed on the front panel adjacent to the button that is required to lock or unlock the controls.

NOTE: These instructions may also work for newer model Maytag, Hotpoint, Admiral and Fridgidaire model front loaders as well. Refer to your owner's manual or front panel for instructions pertaining to your sepcific model.

If the Control Lock feature will not lock or unlock the appliance, unplugging the unit for AT LEAST 30 minutes is recommended in order to reset the main control board. In many cases this is all that is required to correct momentary glitches.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Mar 14, 2009 | Kenmore Washing Machines

1 Answer

Control door lock light stuck 'on'


Unplug it for 40 minutes to reset.



This advise is for Kenmore Elite and Whirlpool Duet front loader washers and dryers with a Control Lock problem.

This may or may not be an indication of a serious problem. In the majority of the cases, this is a simple operator error. Nearly all these model appliances have some sort of Control Lock feature on the front panel now. This is a designed safety feature that is used to prevent small children from manipulating the controls. The controls can be easily locked or unlocked by pressing and holding the following button on the front panel:

Whirlpool Duet Washer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Whirlpool Duet Dryer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Kenmore Elite Washer - Press and hold the DRAIN/SPIN button for 3 seconds.

Kenmore Elite Dryer - Press and hold the AUTO DRY LEVEL button for 3 seconds.

These instructions may not be all inclusive for all Kenmore and Whirlpool models, but they are the most common. Chances are, if you have a Control Lock feature, the instructions will be printed on the front panel adjacent to the button that is required to lock or unlock the controls.

NOTE: These instructions may also work for newer model Maytag, Hotpoint, Admiral and Fridgidaire model front loaders as well. Refer to your owner's manual or front panel for instructions pertaining to your sepcific model.

If the Control Lock feature will not lock or unlock the appliance, unplugging the unit for AT LEAST 30 minutes is recommended in order to reset the main control board. In many cases this is all that is required to correct momentary glitches.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Dec 30, 2008 | Kenmore Elite 45986 Front Load Washer

1 Answer

Whirlpool Duet Ghw9150pw1 would not start


This advise is for Kenmore Elite and Whirlpool Duet front loader washers and dryers with a Control Lock problem.

This may or may not be an indication of a serious problem. In the majority of the cases, this is a simple operator error. Nearly all these model appliances have some sort of Control Lock feature on the front panel now. This is a designed safety feature that is used to prevent small children from manipulating the controls. The controls can be easily locked or unlocked by pressing and holding the following button on the front panel:

Whirlpool Duet Washer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Whirlpool Duet Dryer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Kenmore Elite Washer - Press and hold the DRAIN/SPIN button for 3 seconds.

Kenmore Elite Dryer - Press and hold the AUTO DRY LEVEL button for 3 seconds.

These instructions may not be all inclusive for all Kenmore and Whirlpool models, but they are the most common. Chances are, if you have a Control Lock feature, the instructions will be printed on the front panel adjacent to the button that is required to lock or unlock the controls.

NOTE: These instructions may also work for newer model Maytag, Hotpoint, Admiral and Fridgidaire model front loaders as well. Refer to your owner's manual or front panel for instructions pertaining to your sepcific model.

If the Control Lock feature will not lock or unlock the appliance, unplugging the unit for AT LEAST 30 minutes is recommended in order to reset the main control board. In many cases this is all that is required to correct momentary glitches.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Aug 21, 2008 | Whirlpool GHW9150 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Sal DeAngelo

Level 3 Expert

2183 Answers

fordexpert

Level 3 Expert

5522 Answers

Ed Mac

Level 3 Expert

731 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...