Question about Makita HM1810 Electric Demolition Hammers

Open Question

What is (60 g) of grease

How much grease do I use

Posted by Anonymous on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What grease or oil do i need to lubricate the bearings and wobble plate on my Karcher pressure washer.

Use a Teflon based grease. Contact an auto parts store to buy it. The grease is usually colored blue.

Jul 16, 2016 | Karcher Garden

1 Answer

How do I change the gear oil in a food service mixer sp62

About 49 results (0.77 seconds) Search Results

    [PDF]Instruction Manual for Globe Mixers - Globe Equipment ...
    Or call the Globe service department at 937-297-7247 and ask for contact .... Please remember that this manual or the warning labels do not replace the need to be alert, to properly train and .... gears or other parts and WILL void the warranty! 7. ... Lubricate the attachment shaft with a food quality grease or mineral oil. 4.

    SP62P 60 Quart Pizza Mixer - Globe
    This mixer comes complete with an 60 quart stainless steel bowl, spiral dough hook and bowl ... High torque direct gear drive transmission; Oil bath transmission.

    Globe SP62P Gear Driven 60 qt. Commercial Planetary ... > ... > Commercial Floor Mixers
    Commercial Planetary Floor Pizza Mixer - 3 HP. In stock ... What is White Glove service? ... Globe XXBOWL-62 60 Qt. Stainless Steel Mixing Bowl for SP62P Mixer.... Planetary grease fitting and gear oil meter. .... Globe SP62 and SP80PL MixerControls .... 2003-2016 WebstaurantStore Food Service Equipment and Supply .

Jan 30, 2016 | Globe Food Mixers

1 Answer

Chair does not raise or lower evenly

Lubricate the mechanism with a spray grease...not oil. You can obtain spray grease from an auto parts store.

Nov 19, 2014 | Home Meridian Comfort Lift Recliner

1 Answer

How do i replace U-Joint on 2007 Suzuki Boulevard c90t

You have to pull the rear drive unit, rear wheel and then access the U joint by normally removing the rear swing arm. Make sure to apply Honda Molt 60 Paste grease to all splines (especially where the driveshaft enters the drive pod (take grease seal off, lube and put new seal on.) This grease is critical to prevent drive failure (seen it lots of times) Join as theres a scad of info there and people who know these bikes inside out

Jul 14, 2014 | 2005 Suzuki Boulevard C90

1 Answer

How do i chack bosch 60 lb jackhammer oil leval

Bosch hammer uses grease available in repair kit. Check ebay or parts house. Remove four hex bolts on the mid section of the hammer and pull off the lower end. Most of the grease goes here. There is a side cover to expose the drive gears if you hear gear noise. Depending on use, only needs grease once a year. Good luck.

Jun 30, 2014 | Makita HM1500B 42 Lb. Demolition Hammer

1 Answer

2002 honda civic ex front end vibrates and knocks at 60 mph

did you do a wheel alignment after replacing these parts also some cv jints need to be greased. also check the wheel balance

Jun 13, 2012 | Honda Civic Cars & Trucks

1 Answer

2001 pontiac grand am gt shaking in the front right end

check your tie rods ball joints to see if they need to be greased or replaced some come from the factory sealed and can't be greased even check the sway bar linkage rod ,but first thing i would do is make sure your new tires are
balanced and check the alignment hope these few tips help you find the cause of the problem



Nov 22, 2017 | Cars & Trucks

1 Answer

Truck does Not Start, No Spark to coil replaced Coil, All spark plugs and wires and battery still doesnt start Tryed using a code reader shows up No codes, Possible Problems?

Ignition Module REMOVAL & INSTALLATION The engine controller is the computer/microprocessor that regulates all ignition functions. All other models (1989-96) employ a 60-way connector. The 1989 models (only) employ an additional 14-way connector. In most cases, the engine controller is mounted in the engine bay to the firewall or a fender. Some early models mount the engine controller in an air duct mounted on the inside left fender. Access to these units hidden in the air duct requires some dismantling of the air duct to get to them. WARNING
Do not remove the grease from the 14-way connector or the connector terminal in the computer. The grease is used to prevent corrosion of the terminals. There should be at least a 1?8 in. (3.1mm) coating of grease on the bottom of the connector terminals. If not, apply a liberal coating of Mopar Multi-purpose grease No. 2932524, or equivalent, over the entire end of the connector plug.
  1. Disconnect the negative battery cable.
  2. Remove the air cleaner duct from the controller, if equipped.
  3. Remove the three module retaining screws.
  4. Remove the 14-way (1989 models) and 60-way connectors from the controller. NOTE: Check the 14-way and 60-way connectors for damaged or bent pins (and correct if any are found) prior to plugging it in.
  5. Installation is the reverse of removal.
prev.gif next.gif

Oct 13, 2010 | 1996 Dodge Dakota

1 Answer

I think my seals on my final drive system are leaking. How do i find out?

If you've got OIL marks on the right hand side of the rear wheel, you've got leaks. That must get fixed or you will wreck the final drive. Keep the level up with 90wt Hypoid gear oil. Some of the seals for the drive unit are hard to come by.

If you have GREASE marks it's not so serious. That could be simply from over greasing the splines, although there is a seal that could be gone. To check, pull the wheel off and clean out the grease.
Always use a 60% moly grease on the splines.

Jun 27, 2010 | 1976 Honda GL 1000 (K1)

1 Answer

Hi - recently bought a new KingKutter 4ft bush

go to and download the manual.

May 15, 2009 | King Kutter Pull Type Rotary Kutter 72in....

Not finding what you are looking for?
Makita HM1810 Electric Demolition Hammers Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Makita Hammering Experts

John Trevino

Level 3 Expert

1388 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

1932 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

20997 Answers

Are you a Makita Hammering Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides