Question about RTO PasLode 900420 Impulse Framing Nailer

1 Answer

My passlode 18 guage finnish nailer fires intermittently. Gas catridgev is good and battery is charged.it now only fires twice after it has been idle for a few minutes.Is this an easy fix?

Have you seen this problem before?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 44 Answers

This is awkward to diagnose. Sounds like a gas problem. Ensure the gas cell is in date. paslode print use by date on bottom. next ensure valve fitted to cell is correct normally yellow. When stopped firing press gas cell door (actuator) does it fire one more time? If yes it could be the actuator getting weak I have seen this cause similar problems to what you are experiencing.

Posted on Apr 11, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 24 Answers

SOURCE: NAILER WONT FIRE NAILS

DO NOT USE WD40 . Is The Nailer fireing? If Not check the micro switch by the fan . Make sure it is pushing on the switch.. Otherwise bend it a little

Posted on Jul 07, 2009

  • 55 Answers

SOURCE: bought paslode 350/90 nailer on ebay did not come with instructio

That is not true you may have it vapor locked look at the firing mechanism in the top front and clean it with degreaser and then very lightly re-oil it and try that before throwing it away

Posted on Dec 02, 2009

rowdy45176
  • 2176 Answers

SOURCE: I have a PASLOAD 325

checkk the safety to make sure it fully depresses. Also check the gas for the expiration date that is on eht bottom and lastly did you replace the O ring in the fan area if it is an older unit. What I do is leave the top cover with the filter off and pull the pusher spring all the way back and then WITHOUT gas OR ATTERY in tool push down to make sure the safety fully depresses. Also did you remember to reinstall the push rods. also look at the gas stem.

Posted on Sep 21, 2010

  • 760 Answers

SOURCE: I changed the gas cylinder in my paslode framing

Make sure you have the correct gas cylinder. There are more than one type of cylinders for these nailers. If it is not correct it won't seat and gas will leak. Whiring sound is normal, fan mixing oxygen. Make sure "O" ring is in place under the gas cylinder.

Posted on Oct 02, 2010

rowdy45176
  • 2176 Answers

SOURCE: The problem of intermittent firing

what is the expiration date on the bottom of the fuel cell?? Also what were the condition of the o rings and did you relube with a good quallity oil. What I would do is remove the front assembly to expose the fan only and then insert a battery, pull the trigger and the fan should run for a few seconds, next there is a roller lever towards the top, depress it keeping fingers away from fan and again it should run for a few seconds, next depress and hold the lever and then pull the trigger and you should see it fire, repeat this several times, that will narrow it down to the spark unit/electronic assenbly or the cylinder.

Posted on Jan 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bostitch GFN1564K cordless nailer brand new wont fire.


take it back to the supplier for a replacement or warranty fix
however as it is electric there may be a safety switch that you have to engage to make it work as it would go off when ever and spray nails and staples every where.

Jun 27, 2015 | Stanley Bostitch Gfn1564k 15-guage...

1 Answer

IMAGE IS NOT SEEN ON SCREEN BUT MENU IS SEEN


The CCD censor or circuit is faulty. Needs camera shop.

Dec 19, 2012 | Kodak EasyShare C613 Digital Camera

1 Answer

Menu is seen but picture is not seen on screen


Hello, Will it take a photo ? Sounds like bad sensor unit. High dollar repair.
Best Regards, Russell

Dec 19, 2012 | Kodak EasyShare C613 Digital Camera

1 Answer

My brand new DC608 18 gauge nailer jams every time on the 2nd nail.


Per your addendum I would have first told you to check that you are using the proper guage nails. Second you should make sure you are loading the nails in the lowest channel in the magazine so they are at the bottom of the magazine. If you load them into the top of the magazine they have more time to go off course before they get into the wood.

May 29, 2012 | Dewalt Heavy - Duty 18 Gauge 2" Brad...

1 Answer

Passlode im250ii


Not much information to go on. first thing to check is the date on the fuel cell. On the bottom of the fuel cell you will find a use before this date. fuel goes bad. next is tomake sure the battery is fully charged (light on tool should be green when you put battery in). With fastners in tool depress on wood. Now you should hear the fan start. Pull trigger and it should fire. If t doesn't, make sure there is not a jambed nail. Open quick release on front of tool. Remove jambed nail push driver back inside tool with small screw driver. Try to fire tool again, you may have to lift the tool again off the wood and press back down. when doing this you are putting fuel in the chamber and you might have to do it more than once. Hope this helps. please give more information if it des not. Good luck

Apr 25, 2012 | RTO Paslode 902000 IM250 Ii Cordless 16...

1 Answer

Miss fire or fireing two at a time how to fix?


first check for the proper guage nails, then look for a jammed nail in the magazine area and also a bent driver and lastly make sure that when fired the piston retracts fully all the above will cause the misfire.

Jan 23, 2011 | Stanley Bostitch 18 Gauge Brad Nailer 1 -...

1 Answer

The problem of intermittent firing began some time ago. Now the gun will not fire at all. The gas bottle is full and the battery is fully charged. I disassembled and cleaned the gun. It subsequently fired...


what is the expiration date on the bottom of the fuel cell?? Also what were the condition of the o rings and did you relube with a good quallity oil. What I would do is remove the front assembly to expose the fan only and then insert a battery, pull the trigger and the fan should run for a few seconds, next there is a roller lever towards the top, depress it keeping fingers away from fan and again it should run for a few seconds, next depress and hold the lever and then pull the trigger and you should see it fire, repeat this several times, that will narrow it down to the spark unit/electronic assenbly or the cylinder.

Jan 09, 2011 | RTO PasLode 900420 Impulse Framing Nailer

1 Answer

Lines are shown when the picture is seen or downloaded on the PC - all across the photograph


If there are no distortions on the picture seen on the camera viewfinder then there is some issue with the picture manager software.
If the images seen on the PC are also showing clean pictures, then there fault on the transfer or the camera driver software.
Remove the SD card and insert into the PC using the card reader- use in any laptop- if the picture is clean , then uninstall the camera driver and reinstall, then connect to transfer. If the fault is seen the download another version from the camera support site to be installed.

Dec 18, 2010 | Fuji FinePix Z1 Digital Camera

1 Answer

Dvd drive not recognized by system drive not listed in system drive/ folder tree device not shown in hardware list under "control panel/ device manager"


Make sure drive is seen in BIOS, if not, re-seat the drive. If still not seen in BIOS reset defaults and check again. If still not seen, replace the drive.

If the drive is seen in BIOS, then use the following to resolve.

http://www.fixya.com/support/r3688895-cd_rom_or_dvd_drive_not_seen_in_windows

Jun 19, 2010 | Toshiba Satellite 4300 Notebook

Not finding what you are looking for?
RTO PasLode 900420 Impulse Framing Nailer  Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top RTO Air Tools & Compressors Experts

yoopertech

Level 2 Expert

131 Answers

John Trevino

Level 3 Expert

1388 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a RTO Air Tool and Compressor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...