Question about Saws

1 Answer

Hegner motor fast

The motor runs very fast

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

You might need a new switch

Posted on Apr 06, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a 1976 115 hp johnson boat motor i have to hold choke in to get it to run fast


remove and have the carburettor serviced as what that indicates is blockages in the main jets and circuits
could be corrosion from, or water in the fuel

Jun 07, 2015 | Boating

2 Answers

Why does the engine spin fast but doesn't start?


Hi Kenny:
Old mechanic's philosophy; If you have fuel, and you have spark, it should run. Some more info would help. Did it run before? What happened immediately before it stopped running?
What is it? Give us some hints and we'll help you get mobile. Cheerfuls.

Mar 19, 2015 | Cars & Trucks

1 Answer

Motor is running fast when i start it chock seems to stay closed engin light is on


A 2000 Isuzu would have fuel injection not a carb, so no choke is used.
You would need to get the computer checked for trouble codes, I would suspect a huge vac leak is the cause of the fast idle.

Jan 31, 2014 | 2000 Isuzu Rodeo

1 Answer

Need schematic


Most of the time when the motor is running to fast it's the pinch roller not doing its job it may need cleaned.

Aug 17, 2012 | RCA RP3503

2 Answers

I have a Teac A-6300 that won't go fast forward or reverse but the capstan motor is running


The Capstan motor is just for the play speed regulation so it has nothing to do with the reel motors. You can have an open safety microswitch or maybe a bad relay. It is really hard to say without looking at the unit but I am sure it is repairable. Is the right dummy plug put in the back? This can stop all transport functions if it is out.

Apr 14, 2012 | Teac Audio Players & Recorders

1 Answer

Its actually a B1500 3.9 v6 my question is on the oil guage its at about 30 when i start driving it go to about 100 but when i stop it go back to 30 is this normal


Yes, this is normal what is going on is that your oil pump is not spinning as fast. your pump runs off the motor and the fast the motor goes ( rmp ) the fast the pump spins and pumps. the motor dose not need as much at low rmp as high rpm. look up toroidal oil pump.
Mark
C.C. Motorsports

Feb 24, 2010 | Dodge Ram B150 Cars & Trucks

1 Answer

1985 gmc k1500 wipers only move at 1 slow spped, interminttent doesnt work at all. How fast is fast and why is fast not working?


Slow is the same speed as 'mist'. Mist is when you twist the control arm backwards to induce a single swipe. If you hold it, you will run the wipers in low speed. Fast is faster than that. Probably by 30% or more.

Turn the wipers on high speed. Wiggle the connector at the wiper motor. If the wipers run sporadically as you wiggle the connector, you either have a bad connector or a bad circuit board on the wiper motor.


Jan 15, 2010 | 1985 GMC K1500

1 Answer

Motor is sluggish, Necchi Model#4795


Set machine to wind the bobbin to check for how fast the machine will run. I believe it will run fast or slow according to how hard you depress the foot control. If it runs fast and slow you have a problem in the machine. Most likely the machine, if turned by hand, is hard to turn and it needs to be professionally serviced. before it is ruined.
sewman7

Dec 29, 2008 | Sewing Machines

Not finding what you are looking for?
Saws Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saws Experts

Bill Boyd

Level 3 Expert

42533 Answers

Tom Chichester

Level 3 Expert

34690 Answers

ray gallant

Level 3 Expert

44198 Answers

Are you a Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...