Removing magic marker

That is a simple dryer door seal. Remove the old one by simply getting it started...normally at the bottom of the door will be the seal when the door seal starts and ends. Grab one end and pull hard. If it rips, don't worry....you are installing a new seal. Once you have the first tab out, make a mark with a magic marker and then continue to remove the old gasket by pulling and wiggiling. Start he new gasket at your magic marker mark and simply continue to press in the slotted tabs until complete. If I can help further.....

Waiting to hear from you,
Eric and Ann Campion

P.S. Please keep in mind we help pay our staff with earnings from parts sales. Help us keep this valuable service free and order your parts from us. Visit our website for additional help at http://www.affordableappliance.com or for Parts Order Only, Call 1-570-622-6441

there is one top screw just remove the one top screw and pull the turn signal and side marker light housing off the fender then replace bulb.

My washer was doing the same thing. I had a magic marker on the bottom of the plastic tub below the inner tub. The agitation cam could not release for spin. I remove the magic marker and she took off.
This video shows how to get the inner tub out:

More here

More here

The side marker light must be removed in order to get at the turn signal light.
There are two screws holding the side marker light which is situated above the turn signal.
Open the hood.
Remove the phillips head screw at the top of the side marker light.
Using a long #2 Phillips screwdriver, remove the screw on the outside of the side marker light. This can be seen by looking between the lower side of the side marker light and the top side of the turn signal.
The side marker can be moved.
The turn signal has one screw on the top of the fixture that must be removed.
Slide out the turn signal fixture. There is a small feature on the lower front corner of the turn signal fixture that you must note to properly reinstall the turn signal.
In order to get to the bulb, rotate the bulb socket 1/4 turn CW or CCW. The bulb socket is loose.
The bulb is simply pressed into the socket.
Not sure of the type, but it can be found at your locale auto parts store.
The bulb is used in several places on the 1994 GC, so get apacket with two, if possible.
Assembly in reverse. Be careful not to overtighten the screws as they are replaced

Hi

The temperature control is normally in the inside top of the unit, sometimes at the back, sometimes at the front.

If you are competent with electrics its a fairly easy repair, only 2 wires and the ground. Do not confuse the interior light wires with the thermostat.

Switch off and unplug before starting work

Undo the screw holding the internal light, remove the cover

Knob generally pulls off or may have a small screw under the knob cap, then find how the casing is fixed, remove the casing the thermostat is fixed either with 2 screws or 1 center knut, be careful when removing the capilliary (looks like a thick silver wire) don't damage it you really will not like the smell.

Replace exactly as removed, takes lots of care and patience, use your cellphone to take images for reference if your not certain

Regards

Gordon

Hi

The temperature control is normally in the inside top of the unit, sometimes at the back, sometimes at the front.

If you are competent with electrics its a fairly easy repair, only 2 wires and the ground. Do not confuse the interior light wires with the thermostat.

Switch off and unplug before starting work

Undo the screw holding the internal light, remove the cover

Knob generally pulls off or may have a small screw under the knob cap, then find how the casing is fixed, remove the casing the thermostat is fixed either with 2 screws or 1 center knut, be careful when removing the capilliary (looks like a thick silver wire) don't damage it you really will not like the smell.

Replace exactly as removed, takes lots of care and patience, use your cellphone to take images for reference if your not certain

Regards

Gordon

The side marker light must be removed in order to get at the turn signal light.
There are two screws holding the side marker light which is situated above the turn signal.
Open the hood.
Remove the phillips head screw at the top of the side marker light.
Using a long #2 Phillips screwdriver, remove the screw on the outside of the side marker light. This can be seen by looking between the lower side of the side marker light and the top side of the turn signal.
The side marker can be moved.
The turn signal has one screw on the top of the fixture that must be removed.
Slide out the turn signal fixture. There is a small feature on the lower front corner of the turn signal fixture that you must note to properly reinstall the turn signal.
In order to get to the bulb, rotate the bulb socket 1/4 turn CW or CCW. The bulb socket is loose.
The bulb is simply pressed into the socket.
Not sure of the type, but it can be found at your locale auto parts store.
The bulb is used in several places on the 1994 GC, so get apacket with two, if possible.
Assembly in reverse. Be careful not to overtighten the screws as they are replaced.

take the head off the jug again take a black magic marker and marker all over the gasket service and then tape 600 grit sand paper to glass or mirror and rubb the head acrossed in a cris/cross pattern and check this will tell you if its warped and (wet) sand it till the marker is gone re applacation might be nessasary if you wan tto sand it or have it milled for 80- 100$ you can check the jug this way too but the stud need to be removed email me at allmotorman1981@aol.com for more info if you cant figure this out

I'm Bruce of DeBruce Polish, our new polish is non-toxic and odorless and non abrasive, should take care of your problem. We designed it for stainless steel, and have faboulous results on ceramic stove tops, and chrome and many other uses. Even removes permanent magic marker. web site will be up soon debrucepolish.com. Phone 612-220-2236.

the magic chef is probably the ptc relay.to the left of compressor is a shield with 1 screw behind it .on top is the relay with 1 wire.wiggle it off .go to repairclinic.com...part#1206838