Question about Hoover Elite Rewind Bagless Upright VacuumVacuum

Open Question

Power switch will not work

On/off switch will not work

Posted by Anonymous on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Beater bar isnt working I have replaced motor on dyson dc18

Be sure you are getting power to the brush bar motor. Power comes from the main switch to the brush bar switch, then to the micro switch that activates when the handle is reclined, then to the brush bar motor. Any openings in the circuit will cause the brush bar motor to not work.

Jan 23, 2017 | Dyson Vacuums

2 Answers

Motor does not shut off

You can change the switch.

Jan 16, 2016 | Vacuums

1 Answer

Can anyone please help, my Miele vacuum cleaner will not switch on anymore.

Most likely problem one of the wires leading to the switch. Ohm them out with a OHM function of a multimeter, while unpluuged , of course. .

Sep 14, 2014 | Miele Vacuums

1 Answer

How can I get power switch to work on hoover spinscrub steam carpet cleaner?

Replace the switch.

Aug 28, 2014 | Hoover SteamVac F5914-900 SpinScrub...

1 Answer

Power switch doesn't work

so replace the power switch you can get one at guarantee vacuum and sewing center

Mar 19, 2014 | Hoover Freespace Evo Pets TFV2015

1 Answer

My henry hoover will not switch on

If you have an elcrical tester you can verify that your source of electricity is in fact working.
next test that the power is getting to the switch.
check that the switch is working properly.If you have power all the way to the motor but it still is not working, then its a safe bet that your motor and/or the capacitor is bad

Oct 31, 2012 | Vacuums

1 Answer

Switch to turn on doesnt work


Remove the switch and see if the switch is bad or if the motor has went bad...

If there is power through the switch then it is the motor...

If there is no power through the switch then the switch is bad...


Nov 26, 2010 | Hoover U5402-900 WindTunnel Vacuum

1 Answer

Kirby stopped working

Here is a guide to diagnosing a problem with your Kirby. I would imagine that your power cord has a short in it or the carbon brushes need replaced. You may want the take a look at my guide for replacing the power switch as well to make sure that it was hooked back up correctly.

Hope this helps...

Jun 15, 2009 | Kirby G4 Bagged Upright Vacuum

3 Answers

Dyson dc14 power button

I just had this same problem tonight. As I was looking on this sight to find a solution, my husband fixed it. First he removed the extended handle part, then he took the 2 screws out behind the power switch and removed the front cover (directly underneath the power button). He then removed the plastic power switch cover and took the power leads off the switch and removed the switch and tapped on it, then the little button stuck in place:) Sounds silly but it worked! Good luck!

Nov 17, 2008 | Dyson DC14 All floors Bagless Upright...

6 Answers

Dyson animal, have to hold ON switch for it to work

Pull the wand out of the Vac. Need to use a small Torx bit to take out 2 screws hidden behind the wand storage. Once screws are out, there are 4 push-clips which need to be un-latched. Pry the power panel off and you will expose the two switches (one for power, one for the brushes). Push the power switch down and it should "release" and go back to clicking when pushed. Re-assemble. Took about 5 minutes to fix.

Aug 06, 2008 | Dyson DC07 Animal Bagless Upright Cyclonic...

Not finding what you are looking for?
Hoover Elite Rewind Bagless Upright VacuumVacuum Logo

Related Topics:

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18394 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1461 Answers

Brad Brown

Level 3 Expert

15618 Answers

Are you a Hoover Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides