Question about Jandy AE3000T-R AE-Ti Heat Pump 137K BTU W/ Chiller

1 Answer

Heater will not come on.

The heater will not kick on. Have reprogrammed the Aqualink to 88 and the heater to 104 and have enabled the Aqualink to the heater.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 372 Answers

You need to put a volt meter on the wire that goes from the Aqualink to the heater and verify that it is telling the heater to turn on. Then we can determine if it an issue with the Aqualink or the heat pump. Make sure that the water temp sensor on the AL is reading actual temp. Sometimes they will read incorrectly and, for example, display that the water is 142 degrees. If the AL thinks the water is already at or above temperature it will not close the switch for the heater to start.

Posted on Mar 30, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Aqualink rs4 manual pdf


hit cancel after that shows up for each program that will get rid of them or you can write down all the information then hit clear memory and reprogram all you auxs

Aug 27, 2014 | Jandy Aqualink RS4 Pool/Spa Combo -...

1 Answer

How do you reset the memory on a aqualink rs6 timer


write down all your auxillaries and if you have acuators because when you reset all is gone go to system set up then clear memory button then reset the button on front of aqualink then reprogram

Jul 29, 2014 | Pool & Spa

1 Answer

How do you fix a fl 7 firemen's switch open message


connect the firemans switch to the heater pins 1 and 2 on the long green plug then enable the heater on the one touch make sure heater is set to highest setting make sure wires go to pool and com then it will work your aqualink will control heat settings

Jun 30, 2014 | Jandy Aqualink - Rs24 One Touch Pool / Spa...

1 Answer

The panel back light on myh Aqualink RS All


I don't think so but go through your menu to see if the backlight is enabled. I have never heard of one burning out unless a surge or something fried the whole unit.

Nov 03, 2009 | Jandy Aqualink Rs4 One Touch Control...

2 Answers

Operating instructions for Aqualink RS8 pool/spa combo panel?


To clear the memory
Push the menu button once
Push the back arrow to "System setup"
Push star * or enter button
Push back arrow till display says " clear memory "
Push star or enter
Push star or enter again to confirm.
You will get a message "erasing memory"
Now you can reprogram system

Nov 18, 2008 | Jandy Aqualink - Rs24 One Touch Pool / Spa...

Not finding what you are looking for?
Jandy AE3000T-R AE-Ti Heat Pump 137K BTU W/ Chiller Logo

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jandy Pool & Spa Experts

David Spradling
David Spradling

Level 3 Expert

4292 Answers

Pj Kiley
Pj Kiley

Level 1 Expert

21 Answers

Bill Jordan

Level 2 Expert

372 Answers

Are you a Jandy Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...