Question about Garden

1 Answer

Help! carburetor pulse oiler on homelite xl chainsaw ut-10694-a

This saw uses the carburetor to pressurize the oil tank. It is not the oiling system on the super 2 which uses a diaphragm on the carb. The oil tube comes from the carb directly and goes into the oil tank to pressurize it, then the oil flows out of the tank and to the adjustable oil valve or if you bypass the adjustable oil valve it would go directly to the chain bar inlet/outlet tube. The carb doesn't seem to be pressurizing the oil tank. When I take the tube off of the carb and blow into the tube the oil comes out at the chain bar where it's suppose to. When I put the tube back on the carb and start the engine the oil goes back up the tube away from the chain bar outlet. Any help on this problem would be greatly appreciated. Thanks, Ron

Posted by on

  • Ronald E Gauthier
    Ronald E Gauthier Apr 17, 2014

    Well I fixed the problem. I changed out the old oil lines for new ones and when the engine is reved up the oil comes out at the chain bar outlet. So thanks for to those who tried to help.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 20 Answers

There is a breather hole somewhere you need to clean it up so you can find it probly on the cap

Posted on Apr 16, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: stihl 180 chainsaw,lack of oil to chain and bar

hi there i had this problem check bar studs make sure there tight bar must be flush on chainsaw body not on stud flange if bar is on stud flange there is a gap so oil leaks out near sprocket and not in bar oil channel

Posted on Apr 24, 2009

  • 1 Answer

SOURCE: Homelite XL, UT 10618-A, 14

This probably is a worn out automatic oiling diaphragm and plunger assembly. If it is like my Super 2, it is right behind the clutch and sprocket. I had to take the sprocket off to get to the little plate held by three small screws. You probably have to remove the plastic covers first to see this stuff. After removing the screws, the diaphragm and plunger should peel off either the plate or the engine housing. Now the fun starts. I found a parts supplier that listed a picture of the little demon and the price was about seven dollars. But I didn't bookmark the site and now I can't find it again. If all this info matches your saw, and you find a parts supplier, please post it. Good Luck!

Posted on Jul 08, 2009

  • 597 Answers

SOURCE: old homelite XL chainsaw pumping bar oil into engine while runnin

Check that the oiler hole and the hole in the bar that it pumps into aren't clogged. The sawdust running under the chain and be deposited in the oiler hole in the bar until it plugs it solid. That will keep the oil from havintg a place to go and build up pressure.

Posted on Sep 23, 2009

dontbother10
  • 2220 Answers

SOURCE: automatic oiler on homelite super xl ao does not

Please see the clarification. Lou

Posted on Oct 05, 2009

  • 3 Answers

SOURCE: Gas/oil ratio mixture; chain oil lubricant

Call their customer service at 1-800-242-4672 there are options to choose for gas/oil ratio mixtures info.

Posted on May 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I set idle on my homelite super2 chainsaw


Homelite XL 2 Automatic Chainsaw - YouTube

? 6:12
https://www.youtube.com/watch?v=qk6nk-JQ-zg
Apr 20, 2012 - Uploaded by Alec Ulm's Busted Knuckles
Homelite XL 2 Automatic Chainsaw ... free to shoot me a question or comment and I'll do my best to answer as accurately as I can . ... Homelite SUPER 2 Chainsaw OILER REPAIR & TEST RUN - Duration: ... HOW TO ADJUST A Homelite Carburetor - Duration: 5:01. by smallenginemaster1 177,482 views.

How to Adjust the Carburetor on a Homelite Super VI Chain ...

homeguides.sfgate.com > Construction & Remodeling > Siding
Homelite Super VI chain saws are equipped with a Walbro HDC diaphragm, and ...Adjust the idle mixture screw and idle speed screws clockwise one-quarter turn at a ...Homelite Super 2 Chain Saw Oil Type · How to Replace a Carburetor on a .... MyRidevisit'Cars-My Ride'navigation-www'4 · Sell Your Carvisit'Cars-Sell ...

Need carb settings for Homelite chainsaw - My Tracto



Jan 03, 2016 | Homelite Garden

2 Answers

I need to remove the automatic oiler in my homelight chainsaw z3850b


Chainsaw Oil Pump Replacement - Homelite ... - YouTube

? 5:57
https://www.youtube.com/watch?v=8dj0Voh3TTM
Jan 21, 2014 - Uploaded by RepairClinic.com
The most common reason for replacing the oil pump is ... ...Chainsaw Oil Pump Replacement - Homelite Chainsaw Repair (part #309514001) ... spark plug wrench, cord, clutch removaltool, adjustable wrench, needle-nose pliers ... The chainsaw guy shop talk Repair Homelite 150 chainsaw Auto Oiler ...

How to Repair a Homelite XL Chainsaw Oiler - Home Guides

homeguides.sfgate.com > Real Estate Advice > Basic Real Estate Advice
The Homelite XL chain saw is designed to use one tank of oil per each tank of fuel. Fill the oil ... Push the guide bar toward the saw, and remove it and the chain. Clean the ... Automatic Oiler and Oil Line Replacement ..... My Ridevisit'Cars-My

Dec 21, 2015 | Garden

1 Answer

Is there a oil ajustment for the bar oiler on a homelite chain saw


Homelite XL auto oiler - YouTube

? 2:44
https://www.youtube.com/watch?v=PnNTJ3xI_wo
Mar 24, 2012 - Uploaded by 343HFD
Refurbished, carb cleaned/adjusted, new filter, fixed automaticoiler. Anyone know the nut size for the bar ...

HOW TO REPAIR CHAINSAW OILER - YouTube

? 6:38
https://www.youtube.com/watch?v=kmUkieIP-vw
Jan 20, 2012 - Uploaded by gregthegardener
lf your chain saw isn't lubing the chain it can cause serious chain ... How to Replace the Bar & Chain Oil ...

Dec 03, 2015 | Homelite Garden

1 Answer

Oil is not going to the chain, it is going to the cylinder or spark plugs smoke is coming out of the cylinder


This only occurs when the oil pump is driven by, or the oil tank is pressurized by, an impulse line. Either the oil pump is defective or a duck valve has failed. With what you give us we can isolate it no further. Provide a model number that leads to a UT- number or preferably the UT-number itself and we can be of more help. You can try to find your saw and oiler parts here:
Homelite/Ryobi.com (authorized parts supplier)
https://www.gardnerinc.com/recons/disclaimer-lg.php - Agree; Choose “Product Line”; “Select OEM” & “Select Catalog” both to “Homelite Consumer Products”. A drop down list appears; self explanatory from here.
The numbers Homelite & Ryobi use do not match the numbers everyone posts. A careful inspection of your saw should find something that matches.

If you have more questions or need additional help please reply below and I will get back to you. HTH & Good Luck.
Lou
Thank You for using FixYa.

May 06, 2010 | Homelite Garden

1 Answer

I have a homelite xl, UT# 10655- the chain oil seems to be leaking and coming out of the exhaust and continues to leak after shutting off the chainsaw. Any ideas on the possible cause?


Your saw is listed as an "XL Chain Saw UT-10655" here:
Homelite/Ryobi.com (authorized parts supplier)
https://www.gardnerinc.com/recons/disclaimer-lg.php - Agree; Choose “Product Line”; “Select OEM” & “Select Catalog” both to “Homelite Consumer Products”. A drop down list appears; self explanatory from here.
The numbers Homelite & Ryobi use do not match the numbers everyone posts. A careful inspection of your saw should find something that matches.
See the "Engine Internals" print. The oiler appears to above the clutch and driven by a pressurized tank. Venting the tank (opening the oil cap) may help help with weeping but only emptying the tank will stop it.

If no oil from engine oiler hole I suspect a failed hose or connection. Use the IPL to inspect and repair as needed.

Oil System Plugged.
  1. Remove the clutch cover, bar, and chain, clean the bar groove, any holes and passages on the rear of the bar (both sides, consider rotating the bar), if equipped with a sprocket nose ensure it rotates easily at least one complete revolution. Clean the saw oiler hole and channel. Insert a blunted, hooked piece of wire through the oil filler hole and pull the hose in the oil tank out. Pay attention to the screen or filter on the free end (clean or replace, difficult to determine serviceability). Start the saw and see if it oils when revved up (oozes down side of saw). If yes reassemble your saw. If no, continue with 2.
  2. Work your way through the linkage (use IPL to identify components and locations) cleaning and replacing any defective parts as you go. Carefully check the hoses for cracks especially at bends and connections. Please take extensive notes & some digital pictures will help during reassembly.
If you have more questions or need additional help please reply below and I will get back to you. Thank you for using FixYa and Good Luck. HTH
Lou

Feb 27, 2010 | Homelite Garden

2 Answers

Working on homelite 20 power stroke saw, installed carb kit & checked complete ignition system & it still floods no matter what you do. also it way over oils the bar. is there a adjustment for that...


Don't know if this is your problem but I experienced it a lot using Homelites. The gas tank sits directly over the cylinder head. As you spill mixed gas with oil over time it coats the cylinderhead with oil and it collects a lot of sawdust and as the saw gets more coated with this mixture it makes it a lot hotter and it doesn't cool down as well. Cleaning the saw will help it cool better and lower the amount of heat. Here in lies the problem. The gas tank cap has a vent in it. This vent over time becomes plugged a lot. As the excess heat from the motor heats up the gas in the tank, it can get hot enough to boil. If the vent is plugged even a little bit it will build up pressure in the tank and force it into the carburetor thus flooding it. I need more model information to find out about the oiler adjustment. If there is one it's usually where the oil comes out of saw and enters the bar.

Oct 15, 2009 | Garden

1 Answer

Homelite ut No. 10748 textron New sitting long


Is there bar oil in the tank? Oil pump and/or pickup tube in oil tank are usual suspects.

Jun 29, 2009 | Homelite ZR10926 16 Chain Saw

1 Answer

Old homelite XL chainsaw pumping bar oil into engine while runnin


Check that the oiler hole and the hole in the bar that it pumps into aren't clogged. The sawdust running under the chain and be deposited in the oiler hole in the bar until it plugs it solid. That will keep the oil from havintg a place to go and build up pressure.

Feb 21, 2009 | Garden

3 Answers

Ryobi Chainsaw - PCN 4545


Ryobi boasts a two year warranty. Have you contacted anyone about a warrantied repair?

An IPL (expanded parts list) for your saw with any oil system detail can be found here:
Homelite/Ryobi.com
https://www.gardnerinc.com/recons/disclaimer-lg.php - Agree; Choose “Product Line”; “Select OEM” & “Select Catalog” both to “Homelite Consumer Products”. A drop down list appears; self explanatory from here.
The numbers Homelite & Ryobi use don't match the numbers everyone posts. A careful inspection of your saw should find something that matches.

Oil System Plugged.
Remove the clutch cover, bar and chain. Clean the oiler hole and channel. Start the saw and see if it oils when revved up. If yes reassemble your saw.
If no a blunted, hooked piece of wire can be used to pull the hose in the oil tank out. I recommend the filter be replaced. Work your way through the linkage cleaning and replacing any defective parts as you go. Carefully check the hoses for cracks especially at bends and connections. If equipped with an oil pump it is usually behind the clutch (clutch is probably left handed thread). Please make extensive notes & some digital pictures will help during reassembly. GL
Lou

Aug 22, 2008 | Makita DCS6401 20 20",64cc Chainsaw 2...

Not finding what you are looking for?
Garden Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2478 Answers

john h

Level 3 Expert

12104 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...