Question about Avanti Kitchen Ranges

Open Question

Need a thermostat

Er24css

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

This thermostat is mounted mid-wall on a brick wall and consistently reads 4 degrees warmer than 2 other thermometers in the room. Can the thermostat be recalibrated? How?


A manual for the thermostat is needed to recalibrating if doable, thermostat model number and brand needed to get the right manual.
A thermostat mount location should be planned. Any holes leading into the wall should be sealed, in other words, the thermostat needs to be insulated and isolated from fake temperature readings, no back drafts or not heat or cooling sources near by.

Jun 23, 2015 | Heating & Cooling

1 Answer

What size wrench do I need to change the thermostat on a 2002 diamante


Were is the thermostat on a 2002 mitsubishi diamante 3.5 v6 ...

www.fixya.com/.../t15150678-thermostat_2002_mitsubishi_diamante_3...
Nov 26, 2012 - SOURCE: asistance to change the thermostat in a 2002 mitsubishi ....size wrench do I need to change the thermostat on a 2002 diamante.

change thermostat change thermostat - Fixya

www.fixya.com/cars/t19454162-change_thermostat
Aug 16, 2013 - change thermostat - Mitsubishi 2002 Diamante question. ... What size wrench do I need to change the thermostat on a 2002 diamante. May 29 ...

Unanswered Mitsubishi Diamante Car and Truck -Q&A

www.dqrkc.com/cars/mitsubishi/diamante/problems
Mitsubishi Diamante - Unanswered Questions, Problems & Issues. Ad ... What size wrench do I need to change the thermostat on a 2002 diamante.

May 29, 2015 | 2002 Mitsubishi Diamante

1 Answer

My air conditioner thermostat keeps losing power


The power for thermostat come to an from the thermostat with the red and common wire. Check for proper connection to thermostat and check thermostat wire from the thermostat to the air handler. Technicians sometimes do not install splices well and sometimes the splices comes loose. I prefer using rtv loaded wire nuts to make splices when I can find them. Another cause for this problem is bad insulation on thermostat wire allowing wire to short out. If this is your problem, you need to replace the thermostat wire itself. If these do not fix your problem, you may need to replace the thermostat itself.
Hope this helps

Oct 20, 2014 | Heating & Cooling

1 Answer

Burner keeps running and heat is coming out of my baseboards with thermostat turned off


Disconnect the thermostat. You can usually do that either at the furnace or at the thermostat.

At the thermostat, remove the cover and find the red and white wires. Disconnect one of them, and leave it in the air.

At the furnace, the thin wires coming out of the furnace go to the thermostat. Usually, there will be a place you can disconnect them.

Once disconnected, the furnace should stop. If it does, you need a new thermostat. If it does not stop, you are in serious need of some furnace repair.

Sep 24, 2013 | Honeywell Programmable Thermostat Heater

1 Answer

Changing thermostat v6


drain coolant until its below the thermostat.then remove two thermostat housing bolts.remove thermostat housing and thermostat.make note position of thermostat before removing it.then carefully clean all old gasket material from thermostat housing and cylinder block you can buy can gasket remover at any auto parts stores.buy new thermostat gasket.if you have the paper type you need to buy RTV SILICONE to help seal gasket if you have rubber type gasket you dont need RTV SILICONE.make sure both surfaces are clean.then install new thermostat and new gasket.if you have paper type gasket apply thin 1/16 coat RTV SILICONE both sides thermostat gasket.then install gasket to thermostat housing then install housing to cylinder block first make sure new thermostat in place before installing thermostat housing. let RTV silicone sit up about hour before adding coolant.IF THERMOSTAT HAS THE O RING SEAL DONT NEED RTV SILICONE AND THE PAPER GASKET.

Jul 01, 2013 | Mercury Sable Cars & Trucks

1 Answer

Thermostat needs replaced


To replace a thermostat, you will need at least: 1. A new thermostat 2. Screwdriver 2. Needle-nosed pliers. Depending on the thermostat and location in your home, you may need more. Make sure the new thermostat you are using to replace the old one with is compatible to your 110-volt housing circuitry. Always turn off the electrical power to the home thermostat at the power panel or circuit breaker box.--------------------------------------------------------------------------
carbrain c168 scanner

Dec 01, 2012 | 1996 Pontiac Grand Am

1 Answer

Need to locate thermostat in 2001 ford escape. i think it is stuck.


Welcome to Fixya

The thermostat is located on the side head of the engine on the drivers side. If you follow the upper radiator hose to the plastic thermostat housing, (this is where it is located). This is a 2 piece housing. 3 BOLTS hold the main water housing to the engine block (These do not need to be removed to change the thermostat. The three screws on the thermostat housing (usually torx heads) need to be removed. (where the upper radiator). Inside you will find the thermostat. Remember to replace the thermostat gasket at the same time and also some thermostats will only fit in a certain way so pay attention when the old is removed if there is a little hole (foget what it is called) at the 12 oclock position on the thermostat.

Thank you for using Fixya!

Dec 09, 2010 | 2001 Ford Escape

1 Answer

Need to find where the thermastat is on a 2003 cadi


It is in the rear of the engine by the firewall and the intake manifold will need to be removed to gain access t it.

Engine Coolant Thermostat Replacement (LA3, LY9) Removal Procedure
  1. Remove the thermostat housing. Refer to Engine Coolant Thermostat Housing Replacement .

  2. 790876.gif
    tif.gif
  3. Complete the following in order to remove the thermostat from the thermostat housing:
  4. 2.1. Depress the ears on both sides of the thermostat. 2.2. Rotate the thermostat until it clears the retaining feature of the housing. 2.3. Release the pressure from the thermostat. 2.4. Pull the thermostat from the thermostat housing.
Installation Procedure

    790876.gif
    tif.gif
  1. Complete the following in order to Install the thermostat into the thermostat housing:
  2. 1.1. Align the thermostat pin to the thermostat housing orifice. 1.2. Depress the ears on both sides of the thermostat. 1.3. Rotate the thermostat until it aligns with the retaining feature of the housing. 1.4. Release the pressure from the thermostat.
  3. Install the thermostat housing. Refer to Engine Coolant Thermostat Housing Replacement .

Jul 10, 2010 | 2003 Cadillac CTS

1 Answer

I have the thermostat set for 70 degrees on the white rodgers programmable thermostat. The heat runs until the room is 70 degrees, but then the heat stops and the room cools off and the heater doesn't kick...


Based on your explanation this is an erratic operation of the thermostat, first thing that you need to check is the wiring make sure that all the wires are proper looped on the under terminals then reset the thermostat if the problem still persist I think you need to replace the thermostat. If you need further support call the homeowner techline 18002842925.

Jan 03, 2010 | White Rodgers White-Rodgers 1F85RF-275...

1 Answer

Honeywell Electric Baseboard Heater thermostat


You need to take the wires off the thermostat. And touch the red and white wire together. If the heater works then you need a new thermostat, if it does not work then you need a new ignitor. It all depends on the t-stat. Dont worry about the wires there are not enough volts to hurt you. It is milli volts so just touch them together and the unit should fire up

Apr 22, 2009 | Honeywell Programmable Thermostat Heater

Not finding what you are looking for?
Kitchen Ranges Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Avanti Kitchen Ranges Experts

Shawn DuRee

Level 3 Expert

355 Answers

ray gallant

Level 3 Expert

43095 Answers

Tom Chichester

Level 3 Expert

34217 Answers

Are you an Avanti Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...