Question about Proform XP 580 Trainer Treadmill

Open Question

Incline function is not working correctcly

When I press the incline button it does not take the command, sometime you see that is trying to go up!!!

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Motorola reset


Hi

Are you talking about voice command on your device or voice command on your phone? Are you doing a long press or a short press of call button? it will behave differently based on how long you press.

Mark
Motorola Support

Aug 19, 2014 | Motorola Mobility Tx500 Bluetooth Car Kit...

1 Answer

Treadmill


Try to RUN the software calibration for troubleshooting.
However test the elevation motor, Lube THE MOTOR : shaft +gear+adjust the small POT for increase performance. see the diagram attached.
God bless you2_4_2013_4_48_38_pm.jpg2_4_2013_4_49_12_pm.jpg

Feb 04, 2013 | Life Fitness Lifestride 9000 HR...

1 Answer

Is there an online repair manual for the Golds Gym Advantage Treadmill? I'm trying to solve an incline problem. The incline does not go up when I push the incline button. I just get a series of beeps...


Your owners manual describes how to perform an incline calibration. Here are the instructions.
Start the machine running. Press and hold the incline up button. While the numbers are changing, remove the safety key. Reinstall the safety key. The treadmill should rise to maximum incline, then lower to minimum. After completing the cycle, the treadmill should function correctly.
If not, you may have a damaged wiring harness (caused during assembly) or a defective incline sensor.
If the sensor is defective, you will need to replace the incline motor.

Mar 01, 2011 | Exercise & Fitness

1 Answer

When i power my Nordic Trac A2050 on it powers up but when I press the speed button or incline button is beeps twice but does not reponse to the command


This sounds like a bad controller. If the machine is under warranty contact the warranty provider. The controller is not hard to replace if you are electrically inclined but it does require calibrating.

Jun 14, 2010 | Nordic Track NordicTrack Treadmill, A2550

1 Answer

Buttons Froze during workout, now none of them work


It sounds like you just need some calibration. To calibrate incline, turn power on press press any incline buttons, as the incline try to change unplug the key. Now re-nsert key and incline will self calibrate,

Aug 23, 2009 | Nordic Track NordicTrack Treadmill, A2550

1 Answer

None of the commands will function


function SubmitGForm() { var ctlForm = document.forms.namedItem('cse-search-box'); var mainForm = document.forms.namedItem('frmSearch'); ctlForm['q'].value = mainForm['_s'].value; ctlForm.submit(); } // Tags: Related Searches: treadmill
--> >> All Products > Microsoft > Windows XP Home Edition > Troubleshooting To solve your problem, re-install Windows, or contact the manufacturer of the hardware for technical support.

May 24, 2009 | Microsoft Windows XP Home Edition

1 Answer

I9900 printer has error 5B00 & won't print


You may need to change the ink absorbers. But try resetting the printer:
Canon I series service mode

1. Start with printer OFF
2. Hold down RESUME and then press and hold down POWER Button.
3. Release the RESUME but continue to hold down the power button
4. Press the RESUME twice, then release POWER button.

Now you have put the printer in Service Mode so it will accept Service commands. Here is the list of Service commands;

A. Press the Resume button once = Print Service test print
B. Press the Resume button twice = Print EEprom data sheet
C. Press the Resume button Three = Initialize the EEprom
D. Press the Resume button Four = Clear Waste INk Counter
E. Press the Resume button Five = Change Destination settings
F. Press the Resume button Six = Head Refreshing (Cleaning)
G. Press the Resume buttom Seven, Eight, Nine, = Not used
H. Press the Resume button Ten = Return to selection Menu

To EXECUTE anyone of the above commands you "MUST Press the Power button one time. Then the function will be executed. After that function has been executed the printer will REMAIN in Service Mode,.. waiting for another command. You can only execute one command at a time. If you are through with all the commands you want to do, just press the power buttom one more time and it will turn the printer off and you will be out of Service Mode. One more note. When you get the printer into Service MOde and it is ready to accept a command, the green light will be on and steady. As you issue a command by pressing the resume button, it will alternate the color from green to orange with each press of the resume button. Remember, if you issue either one of the commands to force a print make sure you have paper installed.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

Jan 13, 2009 | Canon PIXMA MP160 All-In-One InkJet...

Not finding what you are looking for?
Proform XP 580 Trainer Treadmill Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Proform Exercise & Fitness Experts

Ross Metcalfe
Ross Metcalfe

Level 2 Expert

128 Answers

Matt Olenzek
Matt Olenzek

Level 2 Expert

297 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Proform Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...