Question about Maytag Atlantis MAV6451 Top Load Washer

Open Question

Can't get the seal nut off of a mav9501Eww washer

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Model MAV9501EWW not spinning but it is pumping


Hello & Welcome to FixYa

When the washer is not spinning however, pump out the water then the problem is with the lid switch that is bad and needs replacement. Please get back to me if you have any other questions.

Kevin

Jan 13, 2011 | Maytag Atlantis MAV9501E Top Load Washer

1 Answer

How to replace rear wheel bearings


If it has drum brakes, you'll need to take off the center dust cap, remove the cotter pin, remove the nut and washer holding the drum on. The outer bearing should fall out, the inner bearing usually stays in the drum, due to the grease seal. With the front bearing and washer off, put the drum back on and install the nut, then pull the drum, allowing to the nut to catch the inner bearing as you pull off the drum, and that should leave the inner bearing and seal on the spindle. Pack the new bearings with grease, install the inner one in the drum and tap in the grease seal in place, but the drum back on and install the outer bearing on the spindle, the wash, nut, cotter pin and dust cover. Tighten the nut snug and turn the drum a few times and snug up the nut. Don't overtighten it.

Apr 29, 2010 | 1991 Volkswagen Jetta

1 Answer

I am replacing the seal on the rear penion i need touqe specs on the nut


PINION FLANGE & OIL SEAL

CAUTION: Following procedure must be used to retain proper pinion bearing preload. Failure to follow procedure may result in premature axle assembly or component failure. Ensure pinion bearing preload is checked before disassembly, as previous pinion bearing preload will be used during reassembly.

Removal

1. Raise and support vehicle. Scribe reference mark on drive shaft-to-pinion flange on differential for reassembly reference. Remove bolts and "U" joint straps at pinion flange on differential.
Disconnect drive shaft from differential.
2. Remove rear wheels and brake drums to prevent any drag that may affect pinion bearing preload reading. Using INCH-lb. torque wrench, measure amount of force required to rotate pinion. This is pinion bearing preload. Record pinion bearing preload for reassembly reference.
3. Using Holder (6719), hold pinion flange. Remove pinion nut and washer. Scribe reference mark on pinion flange-to-pinion for reassembly reference. Using appropriate puller, remove pinion flange from pinion. Remove oil seal from axle housing.

Installation

1. Ensure oil seal surface in axle housing is clean. Coat lip of oil seal with gear lube. Install oil seal using appropriate seal installer. Drive oil seal into axle housing until oil seal installer contacts axle housing.
2. Install pinion flange on pinion with reference mark aligned. Using appropriate pinion flange installer, install pinion flange on pinion.

CAUTION: Washer must be installed on pinion with convex side of washer facing outward (away from pinion).

3. Install washer on pinion with convex side of washer facing outward (away from pinion). Install NEW pinion nut. Tighten pinion nut to 210 ft. lbs. (285 N.m). Rotate pinion several times to seat pinion bearings.

CAUTION: DO NOT overtighten or loosen then retighten pinion nut when adjusting pinion bearing preload. If pinion nut is overtightened, collapsible spacer on pinion must be replaced.

4. Rotate pinion using INCH-lb. torque wrench. Rotating torque should be equal to reading recorded in removal step 2) , plus 5 INCH lbs. (.056 N.m). If rotating torque is low, tighten pinion nut in small increments until proper rotating torque is obtained.
5. To install remaining components, reverse removal procedure using NEW "U" joint straps and bolts. Ensure all reference marks are aligned. Tighten bolts to specification. Check lubricant level and add if necessary.




Jan 23, 2010 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

I have a maytag washer MAV9501EWW that has a bad odor. Looking at the website and it refers to being HE and using normal detergant instead of HE. Is it HE? No where in the manual does it talk about being...


do a full load of whites, lots of bleach, extra wash/heavy duty cycle, hot wash and hot rinse, not too much soap. this usually works, like a washer flush.

Aug 19, 2009 | Washing Machines

1 Answer

My maytag washer mav9501eww does not spin, but it drains and it does agitate


Not sure if this will help, but I had the exact same problem on a Maytag top loader. With the machine powered off, spin the wash drum clockwise with your hands. It should be very loose initially and then will tighten up. Unfortunately I don't know the exact mechanism that makes this work, but it did work for mine.

I hope this helps...good luck!

Feb 23, 2009 | Maytag Atlantis MAV6000 Top Load Washer

1 Answer

Spins only with manually start /spin sounds like jet engine


Throw this machine out; it is a piece of junk. Transmission shaft is probably scored up so new bearings will do you no good. I cannot see your repyl due to some tech issue w/ the site, so it may be a day or so before I can reply again. Please leave feedback for me if appropriate. Thanks

Nov 28, 2008 | Maytag Atlantis MAV9501E Top Load Washer

1 Answer

Problems with MAV9501EWW Washing Machine :(


your seals and bearings are bad do you wash a lot of sandy gritty clothes if you do that is the cause of the problem

Jan 19, 2008 | Maytag Atlantis MAV9501E Top Load Washer

Not finding what you are looking for?
Maytag Atlantis MAV6451 Top Load Washer Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...