Question about HP Laserjet Pro 400 Mfp M425dn Multifunction Laser Printer

Open Question

Ready 2 download message

When power on

Posted by Anonymous on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


default must be no password , here are the steps to reset the printer
NVRAM reset for the HP LaserJet 400 colorMFP M475dn (Confirmed functional) 1: Print configuration page before beginning reset
2: Disconnect all cables except for power
3: While printer is in ready state, note the position of "Ready" message on the screen (Probably bottom right)
4: Power off the printer via power button
5: Touch the location on the screen where "Ready" message appeared.
6: while touching the screen, power on the printer. Continue to hold the screen.
7: When "Memory Limit Reached" message appears, release the screen.
8: Printer will reboot, clean and calibrate
9: Return cables to their appropriate ports
10: Print configuration page to confirm settings are cleared. Restore settings desired manually.
Finally have access back!

Mar 08, 2017 | HP Computers & Internet

1 Answer

How do I reset a hp LaserJet 3055

Soft reset:
1. Press Menu. 2. Simultaneously press and then release the * button and the # button to open the developer's menu. 3. Press the < or > button until the message REINIT FFS appears on the second line of the control panel display. 4. Press . 5. The process takes approximately 2.5 minutes. During that time, the control-panel display will change several times before returning to Ready. 6. When the Ready message appears on the control-panel display, press Cancel to exit the developer's menu.

NVRAM reset:

1. Turn off the all-in-one. 2. Press and hold down the * and 5 buttons. 3. Continue to hold down the buttons while you turn on the all-in-one. Hold the buttons throughout the entire power-on sequence. 4. When Permanent Storage Init. appears on the control-panel display, release the buttons. 5. When prompted, set the language and telecom country/region. 6. Allow the all-in-one to return to Ready before using it.

Best of luck..

Oct 12, 2014 | HP LaserJet Office Equipment & Supplies

1 Answer

Hi, we have a C525A but has not been used for the last 2 years. When I started it today I got an error code 016-370 with message Reboot Printer. I have powered it down and up for several times but didn't...

You need to switch off the printer and then connect it via the USB cable. Press the hold and cancel buttons simultaneously. Then power on the printer again. On your LCD display you should typically see a message saying 'ready for download mode'. You will then need to initialize the firmware update process. LCD will change to the writing mode. 10 minutes later you will be prompted to start the printer again.
Keep me posted abt the end result...

Oct 11, 2010 | Xerox DocuPrint C525A Laser Printer

1 Answer

What can i do to stop freezing in nokia 2626. if i power on my nokia 2626, the phone hangs after some seconds and i don't know what to do

Nokia models starting with 2 series are generally very slow. Once it is started it will be back to normal. It will take about 3 minutes to start up. Please wait during that period. Once it is started you can use everything except messaging, which will take another 10 more minutes to get ready. Till then it will show the message "Message storage memory not ready".

Jul 05, 2010 | Nokia 2626 Mobile Phone

1 Answer

Have an iriver H10 - i turn it on and i get this message. " System files missing. To restore the system files, connect H10 to iriver plus" I did this and nothing worked? Can u help?

upgrade the firmware of your device follow this... How to upgrade firmware
1. Download the zipped file for your region.
2. Unzip the file and you will see *.exe file.
3. Connect your H10 to PC via provided USB cable and power on H10.
4. Once the device is ready, run the *.exe. It will automatically copy the firmware to your H10.
5. The progress bar copying firmware will be shown and your H10 device will give you 'Busy' message.
6. Once it's done, it will give you 'Upgrade Complete' message.
7. Please disconnect H10 with 'Safely Remove Hardware' option on your PC task bar.
8. Turn on the power of H10, go to 'Settings -> Extra ->Firmware Upgrade' and select 'Yes'.
9. Your H10 device will shut off automatically once the firmware upgrade is complete.

Jun 06, 2010 | iRiver H10 MP3 Player

1 Answer

Hp cm1312nfimfp (ready 2 downlod) problem

You have a printer with a firmware corruption

Try downloading the firmware from the website for your printer product number cc431a. There is a new firmware which was just released today. try downloading the firmware and sending the firmware while the printer is off,

If this does not work the formatter board is damaged and it will need to be replaced.

you can also try doing a hard or reset or nvram:
1. Turn the printer off
2. Hold down the right arrow and the cancel button
3. Reboot the printer while holding the buttons and hold until permanent storage is displayed. Let go of the buttons and wait for the ready message on the display.


May 17, 2010 | HP Laserjet CM 1312NFI Color Printer

1 Answer

The power comes on (I can hear the fan); the LCD flashes on briefly (about 2 seconds) then nothing happens. No READY message on the LCD, no error messages... I can power the printer off with the power...

Most likely power supply. These Samsung 2000 series laser printers are notorious for bad capacitors in the power supplies. Pretty simple repair IF you can get a good tech who can pull out the power supply (not hard) and replace 5 capacitors on the power supply board. A good price to pay would be in the $100 range for parts and labor.

Jan 28, 2010 | Samsung ML-2550 Laser Printer

1 Answer

Sign in problem with yahoo messenger ? Error Message 81003004

This is a beast of a problem believed to be created by a Yahoo update and firewall settings. You have 2 possible solutions to try.
1) Clean uninstall and download a current program
2) Clean uninstall and download a 8.0 version

1) Close all programs when uninstalling, downloading and uploading
2) Save your Profile folder to a CD if you wish to retain your message Archives.
3) Download Revo uninstaller - this will use the Yahoo software to uninstall and follow it up with a computer scan after to look for any software left behind and offer it up for deletion.
4) When you are ready to run Revo, double click on the Yahoo Messenger software and then select the 'Advanced' mode from the Revo options
5) Allow the uninstall and scan to function, if the scan offers anything up for deletion select everything and delete it.
6) Download ccleaner and run it through until clean
7) Shut down computer
8) Power off your router for 1 minute
9) Restart computer
10) Download Messenger from here - use the links for the version you want
11) Before downloading your choice check the 'Technical tab' to ensure you have the necessary Operating System

Oct 11, 2009 | Yahoo Messenger

1 Answer

Error Message 016-370 restart computer

turn off the printer

1. Connect the printer through USB.
2. hold the enter button (the one in the middle of the circle) with the cancel button simultaneously
3. turn on the printer you will see the following message on the LCD screen
4. " download mode… ready"
5. Start the firmware update from the computer.
6. The LCD will change to "writing…"
7. After about 10 minutes it will prompt you to restart the printer.

Nov 27, 2007 | Dell 5100cn Laser Printer

Not finding what you are looking for?
HP Laserjet Pro 400 Mfp M425dn Multifunction Laser Printer Logo

Related Topics:

195 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2022 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides