Question about Lexicon Music

Open Question

Don't know how to hook it up

I don't know if i go main output into amp

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I hook up the speakes with 1 main main and one main monitor?


Need more info, how many main speakers and monitor speakers are you trying to plug into the unit?

May 04, 2014 | Peavey Xr 8600 8 Channel Powered Mixer

1 Answer

I want to purchase a behringer 15 band graphic equaliser and connect it to a numark 5000fx mixer via skytec pro600 power amp can you help.


The signal path to follow is explained below:

*Audio Source(Cd/LapTop/Ipod)output to,
*Numark 5000FX Input, Then master/main outputs go to,
*Behringer FBQ1502 Inputs, then outputs go to,
*Pro600 Power Amplifier Inputs, then power amp outputs hooked up with a speaker each side.

Hope this helps.

Nov 06, 2013 | Behringer FBQ1502 Ultragraph Pro Dual...

1 Answer

I want to know how to connect a powered subwoofer to the peavey 10 mixer


Connection is hooking up from mixer's main outputs (L,R) to
Subwoofer amp inputs.

Oct 10, 2013 | Peavey Electronics Peavey PV10 Mixer

1 Answer

Help with hooking up a compressor for vocals.


The compressor is a really good idea and should be connected between your mixer and your amplifiers. Your "integrated" mixer/amp is a bit tricky in that you will have to "insert" the compressor in the signal path.

If you have the "console" model....

1. "Main 1 Out" left and right to the input of your compressor and the output of the compressor connected to the "PWR Amp Insert."

2. What is known as Tip, Ring, Sleeve patch cable and plug connected ONLY to the "PWR Amp Insert." This type connection breaks out into a "Input" and "Output" using a single 1/4 stereo plug.

If you have the "square box with knobs on front" model

1. "Main Output" to input of comressor and compressor outputs to "Input to Main" (aka "AUX IN").

Check your owners manual for hookup details or suggestions and remember, all outputs feed inputs and all inputs feed outputs.

Oct 29, 2012 | Behringer Music

1 Answer

Hi, How do I connect a powered subwoover to my PMP 6000 when i have connected 1 pairs of passive speakers to Output B and 1 pair of passive monitors to Output A . Ampmode switch set to Monq1 and Mono...


hi,
this mixer has output's from cd/tape(rca plug) that can be used to connect an additional amp for output to a sub. It is designed to use for recording but may also server as a pre-amp output to an external amp of choice.
GL
hope this helps

Don't forget to rate my answers
Thank You
Jammer

Sep 26, 2011 | Behringer PMP6000 / B215XL Powered Mixer...

1 Answer

I'm using the Peavey XR 8600 with two EV Force i 25 speakers. My question is this, what is the difference between the two outputs on the Peavey? I naturally assumed one was left and one was right....


DO NOT parallel more than two 8 ohm speakers on either output and you will be OK. You could also use one speaker on each output. That would be easier on the equipment as it would be an 8 ohm load on each instead of a 4 ohm load on one of the internal amps. If you want to drive stage minitors, then you existing setup is fine and you will connect the monitors to the second speaker output and set the Mon switch as MAIN/MON.

Aug 23, 2011 | Peavey Xr 8600 8 Channel Powered Mixer

1 Answer

We have a pmp6000 mixer hooked up to our ep 4000 and b1800 and b2520,it seems we can only hook up the amp to the mixer into either mono's 1 and 2 or the main 2 however not in main 1 with full...


MAKE SURE the cables you plug into 1/4 inch mains are TRS plugs, and not mono cables (TS). The main output 1/4 inch jacks are TRS balanced outputs and if you plug mono (TS) cables that shorts out the ring connector reducing the power by 6 Db. USE ONLY TRS balanced cables for interconnects !!!! Also read my tip on Fixya regarding PMP mixers. If you use 1/4 inch SPEAKER cables or adapters, if you short the SLEEVE of channel A output to ground you can pop the channel A amp. The TIP of channel B is the hot BUT the SLEEVE of channel A is the HOT. The ttip I posted explains why this is and it isn't mention in the Behringer documentation.

Aug 06, 2011 | Behringer EUROPOWER EP4000 4,000-Watt...

1 Answer

I would like to know I have 2 subwoofer with amp how can I connect it the best way thank you


first, you will need a passive crossover, i do not believe that the mono out of the mixer has a crossover., if the amp does not have a crossover. you could use the "mono" output, and split the signal, with an adapter, to both channels of the crossover, then run both of the low outs to the 2 channels of the amp. or, you could hook the crossover to the main laft and right outputs of the board. send the 2 low outs, left and right, to the subs' amp, and send the two high outs, left and right, to the main speakers' amp.

Nov 24, 2010 | Mackie 1604 Vlz3 16 Channel Mixer

1 Answer

Hello, What is the proper way to connect an Ashly XR1000 Crossover and a Pyle Pro PTA1400 power amp to my Peavey XR8600 so I can use 2 subs? The subs are not powered, but do have a passive crossover...


Here is a link to the manual:http://www.peavey.com/assets/literature/manuals/00513220_7.pdf I didn't look at the manual for the crossover but this is probably the way I would do it. Look at page 13 in the manual : Come out of the Main out (31 in the diagram) into the main in of your crossover. Go out of your crossover Hi and Mid out setting back into Power amp In 1 (labelled 32 in the diagram). Hook your speakers that you normally use to the output jacks on the back of the Peavey. Make sure you match the output impedances. Go out of your crossover low output into the Pyle power amp and out of the Pyle into your subs. Make sure the impedance ratings of all your speakers match the output impedances of your amps. You will only be running in Mono mode as that is the signal output of the Peavey mixer. You can run faux stereo by using the Main monitor Out as 1/2 the pair and the Main Out as the other 1/2 to both channels of the crossover but you won't be getting a true stereo pan mode.

Aug 22, 2010 | Peavey Xr 8600 8 Channel Powered Mixer

1 Answer

Alesis sr16: How do you hook it up??


Come from the main outputs, probably labeled L/mono and R and connect those to your mixer for your audio system on either stereo mix input OR two two inputs that are panned opposite.. DO NOT connect this to a consumer type stereo system as you may blow the speakers or amp. Consumer stuff just isn't able to take output from music equipment such as this UNLESS the volume is kept very low.

May 23, 2010 | Alesis Sr 16 Stereo Drum Machine

Not finding what you are looking for?
Music Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexicon Music Experts

Michial Gueffroy

Level 3 Expert

1138 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Lexicon Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...