Question about Swanson Meteric Speed Square Aluminum

Open Question

Need manual for Swanson Speed Square, Aluminum

Need Manual

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 142 Answers

SOURCE: need to know how to figure a rafter cut

Assuming you already know the angle you require, take the edge with the level on it(if you have that model) or the side that hangs over and hook it on the edge of the board. If you look at the top, on the 90 degree end, it says "pivot", and that is where you will spin the square around. You read on the 45 degree end that was hooked to the board for you angle. If you are trying to cut a rafter at a specific pitch such as a 6/12 you will spin the square around until the 6 on the Common scale lines up with the edge of the board. The Hip/Val scale is for cutting hips and valleys for the roof structure.
If you have any other questions, feel free to contact me here

Bob

Posted on Sep 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 Nitro bass boat 640 LX. Where can I get an owner's manual?


Boat Manuals Now Available Free From Vessel Vanguard ...

www.passagemaker.com/.../boat-manuals-now-available-free-from-vesse...
Nov 14, 2013 - Boat owners are often frustrated by the diffi. ... I need complete operating manual for 2001 Nitro 175 Sport Fish ski boat. Peter Swanson April 6, .... I am looking for a Manuel for my Italian made 1997 AquaViva Frontier 6 meter cruiser. Thank you,. Jeff ... Have purchased 1989 Pro Craft Stalker 180 Bass Boat.

Aug 26, 2015 | Nitro Boating

1 Answer

Why is a speed square 7 inches ?


Hi Joe,

Yes it is 7" X 7". I offer two videos to enjoy its usefulness. Extreme How To Original Swanson Speed Square


Here is a stair layout 12" X 12" with attachments Swanson Big 12 Speed Square . I prefer stair gauges and a layout square. Either method s good.


Here is the link for a variety of topics and input on the uses of the squares for your library.


Fare. Well. Swanson Big 12 Speed Square for Stringers

Dec 31, 2014 | Office Equipment & Supplies

2 Answers

Where do I find manuals for Shimano Tyrnos 10II reel


Hello
Get into this video
www.youtube.com/watch?v=ywf3NZG_xvU

Jan 04, 2012 | Boating

1 Answer

When I try to cut a 45 it seems to be cutting a little more than a 45. how do I adjust it?


Make sure the blade is 90 deg vertical to the saw table. Make sure the indicator is set approprately. Raise the blade just enough to clear the table/base. Place a swanson speed square against the fence and blade. Make sure the indicator is at 90 degrees. Here you might want to tilt the square and check that the complete blade is flush against the sqaure as high up as possible. Lay the square back flat on the table and pull the blade toward you as much as possible. The teeth on the blade should ride against the square extented completely out.

Now set the square against the fence with the 45 degree angle coming away from the table and set the blade on the 45 deg mark on the insicator scale.
The blade should touch the square all the way out fully extented.

Or just experiment with some scrap and check

May 19, 2010 | Dewalt 12" Beveling Sliding Compound Miter...

1 Answer

Need to know how to figure a rafter cut


Assuming you already know the angle you require, take the edge with the level on it(if you have that model) or the side that hangs over and hook it on the edge of the board. If you look at the top, on the 90 degree end, it says "pivot", and that is where you will spin the square around. You read on the 45 degree end that was hooked to the board for you angle. If you are trying to cut a rafter at a specific pitch such as a 6/12 you will spin the square around until the 6 on the Common scale lines up with the edge of the board. The Hip/Val scale is for cutting hips and valleys for the roof structure.
If you have any other questions, feel free to contact me here

Bob

Sep 11, 2009 | Swanson Speedlite Level Square

1 Answer

KNOWING RISE OVER RUN HOW DO I USE THE SQUARE TO MAKE MY ANGLE?


Run is alway 12".
Example 4" (rise)/12" (run)
Measure 4" on one leg of the square and 12" on the other leg. Connect the points and there your angle.

Jun 29, 2009 | Swanson 119 High Visibility Speed Square

1 Answer

Humminbird 7300211 speed unit


Hi!
Installation of the speed/temp wheel is quite easy, here's a manual:
SW Speed & Temp
The new sensor cable plugs into the square plugin in back of your Humminbird....it's the small square connector with 4 holes.
Best of luck!
Mike

Apr 30, 2009 | Humminbird 7300211 SW Speed Sensor GPS...

Not finding what you are looking for?
Swanson Meteric Speed Square Aluminum Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Swanson Measuring Tools & Sensors Experts

Vuk B

Level 3 Expert

678 Answers

Brad Brown

Level 3 Expert

15557 Answers

Tom Chichester

Level 3 Expert

34102 Answers

Are you a Swanson Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...