Question about Margaritaville Blenders

Open Question

Replace coupler need to replace lower coupler

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you replace drive coupler on cooks XB9218WA


There would be no spare parts for that. Best plan would be to fix it with epoxy putty. Seal the lot together, if it fails again, you need a new one.

Jun 08, 2017 | Blenders

1 Answer

Model HR7772. Where can I get a plastic coupler driver?


Check with a local appliance parts supplier and/or Philips to determine availability and source.

Oct 10, 2015 | Philips Blenders

1 Answer

Replacing drive side coupler on a Waring HPB300 blender. Threads don't match???


There are not normally any tricks, sometimes they are left hand thread though. More likely if the thread size is really too small then wrong part has been supplied.

Jul 10, 2015 | Waring Megamix Commercial Blender Hpb300

1 Answer

How can I change the blade for my 2 speed hand mixer? The model type is NC-12 if you need to know


you are using your KitchenAid blender and it stops blending, you may think there is a problem with the motor in your machine. However, a common reason for the blades not rotating in the blender is a dirty or faulty coupler. The coupler is what connects your blender dispenser to the motor, and you can easily replace the coupler at any time by only using a screwdriver.
Things You'll Need
  • Flat-blade screwdriver
    • 1 Turn the blender dispenser clockwise and lift up to remove it. Set the blender dispenser aside.
    • 2 Insert a flat-blade screwdriver between the black drive coupler and the frame of the blender on the top center portion of the blender.
    • 3 Lift the screwdriver upward, and the coupler will start to bend out of place. Slightly turn the coupler and then lift up on the screwdriver again.
    • 4 Continue to move the coupler slightly and lift the screwdriver until the coupler is completely removed.
    • 5 Insert the new coupler over the blender's motor blade and then twist the coupler counter-clockwise until it is tightly fastened.

Jun 07, 2011 | Blenders

2 Answers

How to remove the cutters on model ksb560mco pctag@verizon.net


The cutters are part of the collar itself and not available as a separate part. If there is anything wrong with them you need to replace the whole collar. The collars are available on Amazon UK, K A Parts as well as other places.

Dec 31, 2010 | KitchenAid KSB560 5 Speed Blender

1 Answer

Rubber coupler on blender sheared off


Yes, it is very easy to fix. You will need a new coupler, which is part number 9704230. There is a set of instructions with video here: http://www.kaparts.co.uk/Howtoremoveablendercoupler/tabid/219/Default.aspx

Feb 13, 2010 | KitchenAid KSB3 Classic Work Top Blender

1 Answer

Rubber wheel that blade goes on, how do I replace it?This is the wheel that makes the blade go around. Mine has broken into pieces and can not use blender.


The piece that you need is referred to as the coupler. The coupler is a breakway part that is designed to shear and/or wear down in the event that the blender is overloaded. This is to avoid damage to the motor.

The coupler may be purchased individually and is an easy repair that can be done at home. You may purchase the part and access step-by-step replacement instructions at the following link:

http://www.mendingshed.com/kacoupling.html

Jul 06, 2009 | KitchenAid KSB3 Classic Work Top Blender

1 Answer

The black rubber that blender sits on is breaking off.


The piece that you need is referred to as the coupler. The coupler is a breakway part that is designed to shear and/or wear down in the event that the blender is overloaded. This is to avoid damage to the motor.

The coupler may be purchased individually and is an easy repair that can be done at home. You may purchase the part and access step-by-step replacement instructions at the following link:

http://www.mendingshed.com/kacoupling.html

Jun 26, 2009 | KitchenAid Kitchen Aid Kitchenaid 5-speed...

1 Answer

The rubber gear that turns the blade in the kitchen aid blender is stripped how do i get a new one or a new blender?


The piece that you need is referred to as the coupler. The coupler is a breakway part that is designed to shear and/or wear down in the event that the blender is overloaded. This is to avoid damage to the motor.

The coupler may be purchased individually and is an easy repair that can be done at home. You may purchase the part and access step-by-step replacement instructions at the following link:

http://www.mendingshed.com/kacoupling.html

Jun 25, 2009 | KitchenAid KSB560WH 5-Speed Blender

3 Answers

I need a coupling for my kitchen aid blender model number KSB5WH3. Can you help?


The piece that you need is referred to as the coupler. The coupler is a breakway part that is designed to shear and/or wear down in the event that the blender is overloaded. This is to avoid damage to the motor.

The coupler may be purchased individually and is an easy repair that can be done at home. You may purchase the part and access step-by-step replacement instructions at the following link:

http://www.mendingshed.com/kacoupling.html

Jan 19, 2009 | KitchenAid KSB5 Professional Stainless...

Not finding what you are looking for?
Blenders Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Margaritaville Blenders Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

john h

Level 3 Expert

12650 Answers

Tom Chichester

Level 3 Expert

36467 Answers

Are you a Margaritaville Blender Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...