Question about Cisco Catalyst 2950 24x10/100 Mbps Networking Switch

1 Answer

How to reset the cisco catalyst 2940 switch throught console

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 87 Answers

By reset, do you mean reboot? if so type reload

if resetting to factory type erase startup-config

Posted on Jun 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Reset password Catalyst 4006 Ethernet Switch


Hi,

Depending on the Supervisor Module model, most likely it's a standard Cisco's "password recovery procedure":

Connect to the console
Reboot the switch (power cycle)
Start pressing Ctrl-C till you get to the BOOTROM
Change boot configuration register to 0x2142 (confreg 0x2142)
Boot the switch. It will ignore confuguration and boot "empty".
Go to "enable mode".
Copy startup configuration to running configuration ("copy start run")
Change boot register back to 0x2102 (conf t -> conf 0x2102)
Write config (write mem)
Reboot

Good luck,

Mike / CCNP, CCDP, CCSP, CCVP

Headset Adapters for office phone system

May 03, 2016 | Cisco Catalyst 4006 Chassis ( 4006)

1 Answer

The power devices that Cisco Catalyst 2960 Series Support?


The Cisco Catalyst 2960-48PST-L can support 48 PoE ports with total PoE power output capacity at 370W. Taking advantage of Cisco Catalyst Intelligent Power Management, the Cisco Catalyst 2960-48PST-L configuration can deliver the necessary power to support 24 ports at 15.4W, 48 ports at 7.7W, or any combination in between.

The Cisco Catalyst 2960-24PC-L can support 24 simultaneous full-powered PoE devices at 15.4W for maximum powered-device support.

The Cisco Catalyst 2960-24LT-L can support eight PoE devices at 15.4W
Cisco Catalyst 2960 Switches for the details

Aug 15, 2014 | Computers & Internet

1 Answer

Advise: Cisco Switch for small business?


I think Cisco Catalyst 2960 & 2960S Series Switches with LAN Lite, Catalyst 2960 Series Switches with LAN Base, and Catalyst 2960-S Series Switches with LAN Base is best choice. You can get more information in http://www.3anetwork.com/blog/cisco-switches-for-small-business/

Aug 04, 2014 | Computers & Internet

2 Answers

Cisco Catalyst 2960-S VS 2960-X Series Switches?


2960-X is manual configurable and 2960-S is smart dont need to configure.

Apr 10, 2014 | Computers & Internet

1 Answer

I forget the console password. i want to reset my password. How to do that? product: catalyst 2948G-GE-TX


You will have to reset the switch and intercept the boot into ROMON mode, then load the config file and change the console password, wright the mem and reload.

Sep 23, 2011 | Cisco Catalyst 2948G-GE-TX (746320878614)

1 Answer

HAVE 24 PORT CISCO CATALYST 2960 SERIES SI ,HOW TO PUT IT BACK TO FACTORY SETING SO I CAN USE ALL 24 PORTS WITHOUT MANAGE..???


Due to the length of the solution I have provided you with a link to the Cisco site on how to reset catalyst switches.

It is not a simple process and you need to read the instructions carefully.

http://www.cisco.com/en/US/products/hw/switches/ps607/products_tech_note09186a00800c4546.shtml

Dec 15, 2010 | Compaq Cisco Catalyst 296024S switch 24...

1 Answer

Can't console cisco catalyst 3500


It's possible that the management port is on another VLAN or is not enabled. Your most reliable bet is to try a serial connection to console in.

Alternatively, there is a procedure that will work even if you don't know the password:

http://www.cisco.com/en/US/docs/switches/lan/catalyst2900xl_3500xl/release12.0_5_wc5/swg/swtrbl.html#wp1028958

Jul 15, 2009 | Cisco Catalyst 2924-XL Enterprise Edition...

1 Answer

Lucent Cajun not talking to cisco catalyst


Not sure what Cat switches you have, but the cajun switch must use the same trunking encapsulation.  Older catalyst switches use ISL trunking which only work with Cisco switches.  Make the port between the lucent and cisco dot1q encapsulation on the cisco trunk port.  Also turn on debugging on the cisco and see what messages are generated.

Apr 27, 2009 | Lucent Cajun P220G Networking Switch

Not finding what you are looking for?
Cisco Catalyst 2950 24x10/100 Mbps Networking Switch Logo

Related Topics:

1,337 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cisco Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Prashant M
Prashant M

Level 3 Expert

2260 Answers

Gareth Tomlinson
Gareth Tomlinson

Level 2 Expert

116 Answers

Are you a Cisco Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...