Question about Dryers

Open Question

1LPX2 need wiring diagram for use in a forward/reverse application with a forward/reversing contactor

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: hampton bay altura 68

Read this on another thread - apparently the solution came from HB's tech support.
Turn the fan speed to HI and then select Reverse.  You should hear a "click" and see the fan reverse direction.  It seems that the reversing relay only works when the fan speed is set to HI.
Good Luck!!
Two Metre Man

Posted on Aug 15, 2008

Ad
mydogisk
  • 50 Answers

SOURCE: cutler hammer a10ano series a-1 contactor

There should be 2 contactors for forward and reverse. you have to wire them so that the power coming in will switch 2 opposite phases to reverse.

Posted on Apr 10, 2009

kdgrayson
  • 195 Answers

SOURCE: hunter reversible window fan made in the 50's.

A simple shaded pole non capacitor type diagram is all the same!
the reversing of the hot legs entry is an either or relay with a normally open and nomally closed set of contacts

Posted on Aug 23, 2009

lucgalman
  • 87 Answers

SOURCE: Fan runs in reverse but not in forward. Motor

There is a capacitor connected on the fan motor it must be broken. The explanation is a bit technical but since your description match on my previous experience, I would conclude that it is really the cause of your problem.

Posted on Oct 07, 2009

  • 91 Answers

SOURCE: MinnKota Endura 50 Runs only in high speed in forward and reverse

the coil pack is likely bad especially since you changed the switch. call minkota and get the bench tast info (very simple) and then order and replace the coil pack about 26 dollars. be very careful how you put the magnet assembly back together and mark the position of the case on the outside before disassembly. order a new seal kit and use locktite on the shaft again when reassemling to seal the shaft tube for water. dont run motor uout of the water much as it uses the water to cool the shaft and you can damage the seals. good luck.

Posted on May 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the wiring diagram for a Nordyne GS3BA-024KA condenser


3 wires for compressor, 3 for fan. 2 comp. wires go to the top of the contactor, the remaining goes to herm terminal on capacitor. 1 fan wire goes to the top LEFT of contactor, remaining 2 go to com and fan on capacitor. You will then have 1 wire left that goes to the com on the capacitor and should go back to the top RIGHT of the contactor. NOTE: IF YOUR FAN MOTOR IS RUNNING BACKWARDS (MEANING AIR IS NOT BLOWING OUT OR UP) swap the to fan motor wires on the capacitor (fan and com) this should reverse rotation. ALWAYS REMEMBER TO TURN POWER OFF AND DISCHARGE CAPACITOR BEFORE TOUCHING WITH INSULATED SCREWDRIVER. Good Luck!

Apr 22, 2017 | Heating & Cooling

1 Answer

Need wiring diagram for forward reverse switch for a 1995 club car golf cart not finding diagram where i am suppose to look,


Finding a free service manual for that golf cart might be difficult. You just might have to bite the bullet and buy one.

Jul 29, 2016 | Golf

1 Answer

Need wiring diagram for forward and reverse transmission shifter


How do you expect an answer when you dont even put what it is that your working on.

Jun 25, 2016 | Ford 555 backhoe

1 Answer

Transmission wont pull in forward gears only reverse,just installed it because other transmission did same thing


Not sure for 98s. But you need to erase the codes to start. If the problem is still there, Check the wiring to the transmission. You need electrical diagrams.

Dec 16, 2015 | 1998 Hyundai Tiburon

1 Answer

How do i reconnect the wires on the high/low and forward/reverse on a 12 volt quadbike


I don't have the diagram. But green wires are always ground. The two yellow wires, if it goes into a plug, plug it in. Most plugs are what I call, iddiot proof. Not meaning you are one. But the plugs will not go to another plug. If you have to put a lot of force to get them to go together. They don't belong together. Just remember that some plugs don't go to anything. They make these harnesses to fit multiple vehicles..

Dec 28, 2014 | Cars & Trucks

2 Answers

My golden companion 2 Gc 321 goes forward when i push reverse and goes reverse when i push forward


Sounds like the motor cables are in reverse at the controller. Check that the red is in the positive and the black wire is in the negative on the controller.

Aug 12, 2014 | Golden Technologies Golden Companion 2 -...

1 Answer

I am working on a Tempstar mdl. T4H324GKA100 serial no. E062042494.The low voltage at the condenser causes the low voltage fuse to blow.I disconnected the comfort alert plug,the does fuse not blow, but the...


ohm out the reversing valve coil, ohm out all wires to eliminate shorts, change wire if needed, you have a short issue, unwire all wire and connect on at a time to find out which wire is causing the problem.

Jan 28, 2010 | Heating & Cooling

1 Answer

Cutler hammer a10ano series a-1 contactor


There should be 2 contactors for forward and reverse. you have to wire them so that the power coming in will switch 2 opposite phases to reverse.

Apr 10, 2009 | Plumbing

1 Answer

C 6 transmission


Forward drive in the C6 requires both the forward clutch AND the low/reverse, one-way clutch, or intermedaite band to engage. Since you have reverse but no forward, the forward clutch is most likely the problem, since it is needed only for forward speeds and does not affect reverse. Sounds like a trans rebuild.

Jul 14, 2008 | 1988 Ford F 250

Not finding what you are looking for?
Dryers Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dryers Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Brad Brown

Level 3 Expert

16043 Answers

Are you a Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...