Question about APC Computers & Internet

1 Answer

Solution to fuse problem

Solution to UPS APC product that shout when power on

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • APC Master
  • 3,320 Answers

Got to APC site and download Power Chute

Posted on Apr 01, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

APC BACK-UPS ES 500VA fails to provide back up during power failure


Get APC Powerchute Personal Edition for free and run it. If it says your battery isnt charged, check its voltage disconnected. Charge it with a car battery charger and see if its still a good battery. If not , replace it. If the battery is good, then check the charging voltage. Should be about 14 volts. if not, check the small transformer on the main board. Should be 120 in and 17 to 18 out. 4 diodes in a bridge for charge. The input to the transf has small fuse into it alone.

Jan 04, 2013 | APC BE500U ES 500 USB BACK-UPS 500VA/300W...

3 Answers

My apc ups cannot produce output


Open it up and check the fuse. or your UPS may have a pop out fuse that may need to be reset

Sep 13, 2011 | APC Computers & Internet

1 Answer

Does a APC UPS have an internal fuse. If yes where can I find it?


Some of the batteries have fuses attached to the batteries. The UPS fuses would be close where the power comes in.

Aug 24, 2011 | APC Smart-UPS UPS System

1 Answer

Dead UPS--Won't Power Up


If it's newly bought, let it charge for at least 10 mins. to be able to power on and can be use. If it's not working then call APC Help Center for instructions on how to replace the product with a working one..

Aug 25, 2010 | APC Smart-UPS 1000VA UPS System

3 Answers

Ups not working on generator power


you will try to change the fuse in ups

Aug 24, 2009 | APC Back-UPS CS 500VA UPS System

1 Answer

HELLOO SREEKIDU GURU,


just chech the relay
power resisitors (voltage dependent resistor failure)
fuse failure.

Sep 12, 2008 | APC (BE500U-WEB) (BE500UWEB) UPS System

2 Answers

Apc


1) Switch Off the UPS and unplug all Loads (like System, Monitor etc.) from UPS.
2) Switch Off the AC Power (Input Power to UPS).
3) Press the UPS Power Switch constantly unless you hear 2nd BEEP Tone. As soon as you are hearing 2nd BEEP Tone, Release the Power Switch.
4) This is COLD START of all APC UPS that will reset any internal problem.
5) If, however, the problem persists, contact APC.

Jul 23, 2008 | APC Back-UPS ES 725 Broadband (BE725BB-TU)...

2 Answers

APC UPS no power


The unit might have a dead battery, blow fuse, or a bad board.
Your best bet is to talk to an APC rep. Worst case, APC has a trade in program, and can give you a discount on a new one.
Good luck.

Try Chatting with an APC Support agent online.
Here is their direct link:
http://www.apc.com/support/chat.cfm
Chat with a Support Agent
Chat with Support for immediate assistance with your APC Back-UPS, Cable, Surge Protection, Notebook and Mobile Device accessories and products. Agents are available Monday through Friday from 8:00 a.m. to 8:00 p.m.

Feb 07, 2008 | Computers & Internet

2 Answers

APC Smart-UPS 1000VA shut down and now will not power on. How do I troubleshoot? No power, no lights, nothing and I've never tried to troubleshoot a UPS before. Where do I start?? :-( Thanks Chris


Hello Chris,

I have a similar unit and there is a fuse inside that can blow. Mine did. It worked again after replacing the fuse.

Another option...check the battery connections.

Another option...are the batteries getting old? If so, when they won't reach a certain level of charge the unit will not power on.

Finally, make sure you don't have a blow fuse or popped circuit braker in your home.

Hope this helps?

Charlie

Nov 21, 2007 | APC Smart-UPS 1000VA UPS System

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top APC Computers & Internet Experts

Shawn DuRee

Level 3 Expert

355 Answers

Cindy Wells

Level 3 Expert

5160 Answers

Jax Planet
Jax Planet

Level 2 Expert

922 Answers

Are you an APC Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...