Question about Blenders

Open Question

Varistor mu503 cual es el valor en ohms y como incrementa su resistencia con la corriente

Posted by Anonymous on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Shutdown refer manual

que tal tengo el mismo problema para programar mi vitamix VM0115A, conseguiste de casualidad el manual o un lugar para descargarlo? no la puedo programar!!! gracias

May 12, 2014 | Vitamix Vita-Mix 34013 VM0115A Touch & Go2...

1 Answer

No power. No lights. Dead.

Use a multimeter in continuity mode ( OHMS) to check the power cord to the unit. After disconnecting check the cord on the unit to the switch control and the motor.
The failure can be due to a trip switch- load trip- , failure of the motor brushes, failure in the selector switches, open wires to the unit or the motor .
Checking with the meter can confirm the fault if you find an open line.

Sep 17, 2011 | K-Tec Blenders

1 Answer

Como desarmar motor licuadora hamilton beach 10 speed

Hello, olman

I was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would take some of my personal time to see if Ican help. Even though this Informational site may not have your exact model orbrand, this site will help you a lot. Here is a site link about everything you want to know about blenders andpossibly yours, from
repair to trouble shooting it.

Please if this helped you at all, if you can find the time and in your heart torate my help and some kind words written would be appreciated for my free help, I would appreciate it.

Here is also my direct link to my own pages of other areas of my expertise forother problems you might have in Automotive, Appliance, and Electronics. DropIn anytime for my help.

Thanks, Mike

Aug 19, 2011 | Hamilton Beach 52252 BlendMaster Ultra...

3 Answers

Kitchen Aid blender KSB560 capacitor exploded

Someday people will learn that MANY of the stepdown convertors are useful ONLY for hairdriers and devices WITHOUT electronics. ONLY use convertors with a big transformer in them for electronic devices. Yes, they are expensive, but so are repairs. Now on to your problem:

The device was probably an MOV varistor transient suppressor.

Trace the circuit out and if it is across the input lines, try one of the same MOV's you find in the surge plug strips.

If the device blew apaart, there is likely further damage. You may be able to get a whole board from an appliance repair company.

Do testing of the unit with a 150 wat lamp in series with the power line.

Sep 08, 2009 | KitchenAid KSB560 5 Speed Blender

1 Answer


Lo siento si mi español es malo - Yo uso un traductor. Contacto Dito Dean y debe ser capaz de conseguir un manual. Número de teléfono Dito Dean debe estar en la propia máquina. Por lo general, será sellado en la parte posterior o inferior. Buena suerte! :)

Aug 27, 2009 | Dito Dean Food Prep BKP-350 Bermixer...

4 Answers

Capcitor Burnt

the capacitor has value printed on it. if it is not burned you can still read it.

Aug 24, 2009 | KitchenAid KSB560 5 Speed Blender

2 Answers

Blender suddenly stopped working while in use, lights are on

The motor has burned out. Check with the manufacturer about warranty status for the blender or exchange it.

Jun 23, 2009 | Kenmore 204101 Single-Speed Blender

1 Answer

Westinghouse WST2000 IntelliBlend

I have had my blender sitting for over a year ( only used it once ) because of the same problem and asked my husband to take a look at it... he opened it ... cut the zip ties took the metal banding off ( note only one side of the motor has the metal banding). What you need to get at is behind the first (I think) resistor. Behind that is a thermal fuse (found at radio shack part # 270-1320 about $1.96). you will need some kind of tester to check the ohms going through it (should read zero) the bad one on mine read 334 ohms and you will need a soldering iron to put it back together. Actually a good project for someone who loves to tinker with this.

Aug 29, 2007 | Westinghouse WST2000 IntelliBLEND Work Top...

Not finding what you are looking for?
Blenders Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Blenders Experts


Level 2 Expert

94 Answers


Level 3 Expert

80263 Answers

Ross Keen

Level 3 Expert

1316 Answers

Are you a Blender Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides