Question about Baumatic B187 Stainless Steel Electric Single Oven

Open Question

How to switch on

OSF600VEN

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace light inside oven


Switch oven off and switch main oven switch on wall off if no wall switch, switch off at main switch board.
Open door and check glass cover if it screws off or has retaining screws. be careful as it could be hard to loosen, once loose unscrew lamp anticlockwise slowly as lamp my break off base if tight move side to side very little and unscrew. get replacement and replace opp to removal. Switch on main switch and test.

Oct 17, 2014 | Ovens

1 Answer

Stove element always on high


If the switch is bad the contacts in the switch are not breaking allowing the switch to regulate the power to the element. The switch will need replacing. unless you are replacing the switch with an exact replacement the wiring can be tricky. many times the company will replace the switch with a different manufacture and the terminals are not in the same location. This can make replacing the switch a bit of a challenge unless you are familiar with how the switch is wired. I would have a service person do this you could short out the new switch if wired incorrectly.

Mar 10, 2014 | Ovens

1 Answer

We need to slam the oven door to switch off the intenal light and make the oven work?


cleaning your oven door switch might help but I would consider replacing the switch. The switches are sealed and cleaning does not work well.
http://www.on-timeappliance.com/ovenrepair.html

Mar 27, 2012 | Smeg F65 Stainless Steel Electric Single...

1 Answer

Burner ignighter will not stop clicking. The burner is not lit, but the clicking will not stop


One of the 4 burner control switches on the front of each burner control valves has failed. Inside the thin ceramic switch there are 2 thin strips of copper that are pushed together by a rotating cam driven by the movement of the burner control knob. One of the thin strips is stuck together.
UNPLUG the unit and only plug it in briefly for testing.
The top has to be opened by removing all 4 burner caps and removing the 4 screws under the burner caps. Remove the caps completely but reconnect one burner cap and make sure it is grounded so you can test the igniter's. The gas burner tubing needs removed then the gas burner support has to be removed to gain access to these switches. To remove the wires from the switch you have to use a jewelers screwdriver to release the 2 wires from the switch one at a time. The switches are in series parallel so if one switch is stuck all 4 igniter's pop. To read out the switches you have to remove at least one wire from each switch and insert a short test wire to read for continuity, The switch that has continuity with the burner control switch OFF is the failed switch.
NOTE: the yellow and orange wires need to be insulated during testing. I use a folded paper bag or torn off strips of a cardboard box Just test briefly....
The part number for the switch is 7403P190-60 (Image search)
http://www.repairclinic.com/PartDetail/Switch/7403P190-60/2326

There are numerous sources for the switch.
Thanks for choosing FixYa,
Kelly

Jul 24, 2011 | Magic Chef Ovens

1 Answer

Whirlpool TXFE366LVQ. When I turn selfclean after few minutes it shuts itself off and displays code F5E2


An F5 error code indicates that you need to check the oven door or the latching switch. The switch is used when cleaning the oven, for safe closure. If you find that the door or the latch switch do not function, you may need to replace them
F5-E2 means latch during clean error; the door and latch switch need checking and possible replacement.

1. If door latched:
  1. Disconnect power from unit.
  2. Check wires and connectors from control to door switch, then from door switch to control. If no damage to wires and all connectors okay, proceed to step C.
  3. Replace door switch.
  4. Re-apply power.
  5. Press and hold any key down for 1 minute to clear F5 failure code from memory. F2 will appear. Press CANCEL and observe for 1 minute to ensure operation is correct.
2. If door not latched:
  1. Disconnect power from unit.
  2. Check wires and connectors from control to latch switch, then from latch switch to control. If no damage to wires and all connectors okay, proceed to step C.
  3. Repeat steps A and B for door switch.
3. Measure door switch (door open = switch open small low voltage terminals). Replace switch if defective.
4. Measure latch switch (unlatch = switch open, CAUTION - oven light contacts are closed). Replace switch if defective.
5. If corrections are made in any step, reconnect power to control. Press and hold any key for 1 minute to clear R failure code from memory. F2 will appear. Press CANCEL and observe for 1 minute to ensure operation is correct.
6. If failure remains, disconnect power and replace control.


Hope helps.

Jul 14, 2011 | Ovens

1 Answer

F5 E1 error. Oven door won't open after running cleaning cycle


1.
If door latched:


  1. Disconnect power from unit.
  2. Check wires and connectors from control to door switch, then from door
    switch to control. If no damage to wires and all connectors okay, proceed to
    step C.
  3. Replace door switch.
  4. Re-apply power.
  5. Press and hold any key down for 1 minute to clear F5 failure code from
    memory. F2 will appear. Press CANCEL and observe for 1 minute to ensure
    operation is correct.

2. If door not latched:


  1. Disconnect power from unit.
  2. Check wires and connectors from control to latch switch, then from latch
    switch to control. If no damage to wires and all connectors okay, proceed to
    step C.
  3. Repeat steps A and B for door switch.

3. Measure door switch (door open = switch open small low voltage terminals).
Replace switch if defective.
4. Measure latch switch (unlatch = switch open,
CAUTION - oven light contacts are closed). Replace switch if defective.
5. If
corrections are made in any step, reconnect power to control. Press and hold any
key for 1 minute to clear R failure code from memory. F2 will appear. Press
CANCEL and observe for 1 minute to ensure operation is correct.
6. If failure
remains, disconnect power and replace control.

Note:
Applies to all F5-E... codes.
F5 - E1

Feb 21, 2011 | Whirlpool RBS275PD Electric Single Oven

1 Answer

F5 error door locked


F5
- E0 Door switches do not agree (condition
exists when door switch is closed indicating an open door, and latch switch is
closed indicating a locked door) 1. If door latched:


  1. Disconnect power from unit.
  2. Check wires and connectors from control to door switch, then from door
    switch to control. If no damage to wires and all connectors okay, proceed to
    step C.
  3. Replace door switch.
  4. Re-apply power.
  5. Press and hold any key down for 1 minute to clear F5 failure code from
    memory. F2 will appear. Press CANCEL and observe for 1 minute to ensure
    operation is correct.

2. If door not latched:


  1. Disconnect power from unit.
  2. Check wires and connectors from control to latch switch, then from latch
    switch to control. If no damage to wires and all connectors okay, proceed to
    step C.
  3. Repeat steps A and B for door switch.

3. Measure door switch (door open = switch open small low voltage terminals).
Replace switch if defective.
4. Measure latch switch (unlatch = switch open,
CAUTION - oven light contacts are closed). Replace switch if defective.
5. If
corrections are made in any step, reconnect power to control. Press and hold any
key for 1 minute to clear R failure code from memory. F2 will appear. Press
CANCEL and observe for 1 minute to ensure operation is correct.
6. If failure
remains, disconnect power and replace control.

Note:
Applies to all F5-E... codes.

Dec 27, 2010 | Whirlpool RBD275PD Electric Double Oven

1 Answer

Error code F5EO


F5
- E0 Door switches do not agree (condition
exists when door switch is closed indicating an open door, and latch switch is
closed indicating a locked door) 1. If door latched:


  1. Disconnect power from unit.
  2. Check wires and connectors from control to door switch, then from door
    switch to control. If no damage to wires and all connectors okay, proceed to
    step C.
  3. Replace door switch.
  4. Re-apply power.
  5. Press and hold any key down for 1 minute to clear F5 failure code from
    memory. F2 will appear. Press CANCEL and observe for 1 minute to ensure
    operation is correct.

2. If door not latched:


  1. Disconnect power from unit.
  2. Check wires and connectors from control to latch switch, then from latch
    switch to control. If no damage to wires and all connectors okay, proceed to
    step C.
  3. Repeat steps A and B for door switch.

3. Measure door switch (door open = switch open small low voltage terminals).
Replace switch if defective.
4. Measure latch switch (unlatch = switch open,
CAUTION - oven light contacts are closed). Replace switch if defective.
5. If
corrections are made in any step, reconnect power to control. Press and hold any
key for 1 minute to clear R failure code from memory. F2 will appear. Press
CANCEL and observe for 1 minute to ensure operation is correct.
6. If failure
remains, disconnect power and replace control.

Note:
Applies to all F5-E... codes.

Dec 19, 2010 | KitchenAid KEBC107 Electric Single Oven

1 Answer

The grill / top oven knob will not operate the grill any suggestions?


It is possible the knob is slipping round and not turning the spindle of the switch, or the spindle is broken inside the switch, or the switch is partially seized up.
Pull the kjnob off the switch, and try turning it on wioth pair of pliers or grips, if that works, then the switch is probably o/k.
Also spray some WD40 onto the switch spindle, and inside the switch.
Please leave feedback.
Thanks.

Nov 13, 2009 | Ovens

1 Answer

FSE7 appears on kitchenaid built in oven


Here is the fault code for F5:E7...

1. If door latched:
  1. Disconnect power from unit.
  2. Check wires and connectors from control to door switch, then from door switch to control. If no damage to wires and all connectors okay, proceed to step C.
  3. Replace door switch.
  4. Re-apply power.
  5. Press and hold any key down for 1 minute to clear F5 failure code from memory. F2 will appear. Press CANCEL and observe for 1 minute to ensure operation is correct.
2. If door not latched:
  1. Disconnect power from unit.
  2. Check wires and connectors from control to latch switch, then from latch switch to control. If no damage to wires and all connectors okay, proceed to step C.
  3. Repeat steps A and B for door switch.
3. Measure door switch (door open = switch open small low voltage terminals). Replace switch if defective.
4. Measure latch switch (unlatch = switch open, CAUTION - oven light contacts are closed). Replace switch if defective.
5. If corrections are made in any step, reconnect power to control. Press and hold any key for 1 minute to clear R failure code from memory. F2 will appear. Press CANCEL and observe for 1 minute to ensure operation is correct.
6. If failure remains, disconnect power and replace control.

Sep 16, 2009 | KitchenAid Ovens

Not finding what you are looking for?
Baumatic B187 Stainless Steel Electric Single Oven Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Baumatic Ovens Experts

ashburton

Level 3 Expert

417 Answers

yadayada
yadayada

Level 3 Expert

76848 Answers

Pie-man

Level 1 Expert

29 Answers

Are you a Baumatic Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...