Cannot talk to 8230 with craft interface

I am guessing this is a Sears Kenmore Elite Dishwasher were dealing with ?? If so follow below if Not what are we talking about?

The FUNCTION CODE 2 is for a USER INTERFACE issue. The PROBLEM CODE 2 can be:
User Interface cannot communicate with main control Panel. (A).Unplug dishwasher or disconnect power. (B). Check connections of gray wires between LCD display module and P12 connector on the control Panel:
Loose User Interface connection. (A). If connection(s) loose, then reconnect.
Faulty User Interface. (A). Disconnect power and replace LCD display and console.
Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts.
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a technician.

I researched this a little bit and You need to check for any signs of water spray a cheap hose clamp seems to be the cause of a lot of this problems also corrosion some DIY individuals have removed the cable to the main control panel found corrosion and cleaned it up now working fine while control panel has a fault in Communication their is No Diagnostic Mode Available because of lack of communication , hope this helps

First, please contact your telecom operator to open relevant businesses, which usually includesCall waitinand Three-way calling.(The name maybe different due to different operator)
After opening relevant businesses, please refer to the following supposed situations to make the settings:
Suppose that, Party A, Party B and Party C need to talk to each other, A is the talk originator, B and C are waiting for the calling.
1. A calls B
A presses Menu key on talking interface to open talk menu, clickAdd talk, then another dialing interface of mobile phone appears, A can make a call to C on this dialing interface.
3. When A is calling C, B just needs to wait.
4. A talks with C, then A can open the talk interface again and clickCombine talking. Then A,B,C can make the three-way call.

http://www.xcardiag.com/wholesale/vcs-vehicle-communication-scanner-interface.htmlhere is the video:http://www.youtube.com/watch?v=yyEEyICkf1o&context=C45ff469ADvjVQa1PpcFP-YPDOHB85F3qGu1E4g0TPX4NUdRb25OM=

F70=CENTRAL CONTROL UNIT HEARTBEAT FAILURE
If a Central Control Unit Heartbeat Failure is displayed, no communication is detected from the Central Control Unit to the User Interface.
F71=USER INTERFACE HEARTBEAT FAILURE
If a Central Control Unit Heartbeat Failure is displayed, no communication is detected from the User Interface to the Central Control Unit.

Repair Sequence:
1. Check for continuity of the User Interface harness.
2. Check wire harness connections to the User Interface and the Central Control Unit.
3. Replace User Interface if drum is rotating.
4. Replace Central Control Unit if drum is not moving

user interface is about $195 New;CCU is about $200. Hope this helps!

My guess would be interface. I don't know what mindows is. Neither does the spell checker.

try to format your phone, and check if thhe problem persists.
FOR SOFT-RESET:

- at Standby Screen type-in => *#7780#
It will ask for “Restore all phone settings-phone’ll restart….”
Then it asks for security code enter factory default => 12345


FOR HARD-RESET:

- at Standby Screen type-in => *#7370#
It will ask for “Restore all phone settings-phone’ll restart….”
Then it asks for security code enter factory default => 12345


FOR FLASHING- TOTAL RESTORE: (Do this if your phone does not boot up)

1) Remove the battery, and then wait for about 20 min or so before putting it back

2) Press and hold these three keys together -Green dial key, Star key[*], Three key [3]

3) switch ON the phone.

4) Do not let go the three keys until you see the WELCOME screen displayed and just let it complete the boot process.

check if this helps. if this doesnt help contact Nokia Care Point-> http://europe.nokia.com/A4388379
thanks for using FixYa

Hi,Try the following sites to short out your problem…..

http://uw713doc.sco.com/en/PR_admin/prntT.NoPrint.html

http://files.support.epson.com/htmldocs/pho22_/pho22_rf/trble_5.htm

http://www.smartcomputing.com/editorial/article.asp?article=articles/archive/r1101/04r01/04r01.asp&guid=

Thanks

maybe this can help you,please try to replace the fan or you can also clean it.. http://www.docs.sony.com/release/PCVW510G.pdf

Sounds like a firmware issue to me, so I would think updating the firmware should help. If not, virginizing it may, but since I haven't encountered this problem, I really can't say for sure.
Good Luck.

i can see them but cant hear them