Question about Panasonic Viera TH-42PX80U Plasma TV

1 Answer

Problem with the main board

I have to change the main board and I can not find it Please tell what can i do in this situation

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Panasonic Master
  • 20,086 Answers

The "Main" board or Control Board has the input connectors on it with the interface connectors that go to the other high voltage panels. Bottom right hand side looking from the rear of the TV. Why would you want to change that panel? The YSUS board is the usual faulty panel. 6 - 8 flashing lights.

Posted on Mar 25, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced main board and power oard I now have power I can tell because the standby light now comes on and lights up and stays on when I power on tv but still have no picture any ideas


After the power board is the board that controls the picture. If your power board was bad, that board may also be bad. (Check for a fuse on _any_ of the boards). Note: If your Plasma TV is 5+ years old, you may not be able to remedy the situation without spending a fortune on guessing bad boards.

Mar 11, 2016 | Vizio 50" p50hdm high definition...

1 Answer

I have a sharp tv model LC-46D82U has no picture on the back have 2 red light on, one flashing other standing, please tell me what is the problem?


Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts.
http://electro-medical.blogspot.com/
http://electronicshelponline.blogspot.com/
In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.

Feb 16, 2016 | Sharp Televison & Video

1 Answer

Lg dryer doesn't turn on


Having changed the main control board, the only other things to check are as follows:
Thermal Fuse, Door switch, Drive motor, Drive belt and Belt switch.
These can cause a non-start situation.

Aug 31, 2014 | LG DLE2301 Electric Dryer

1 Answer

Wont boot up


Remove main battery from laptop and plug in adapter, if the computer fires up the battery is bad, no change, have the adapter tested, if okay, the problem lies in the motherboard, sometimes the DC jack works it's way loose breaking connection from main board, at this point it must be dismantled to address the situation.

May 14, 2012 | Compaq Presario 1275 Notebook

1 Answer

Error code e10 on zanussi zjd1219


E10 on the drying cycle normally indicates a failure to take in water during drying
this is usually a failure of the triple water valve unplug your unit take the top off you will see the valve at the rear of the appliance change out the water valve and you should be up and running again the service manual states that it could be the triple water valve , the wiring , or the main control board if you have any further questions message me back and please remember to rank how this opinion has helped in your appliance situation it allows me to help others in similar situations Thanks Rick

Mar 23, 2011 | Dryers

1 Answer

My dash board from my mitsubishi galant went off


Can you please turn on your headlights to full beam, and confirm if you have strong brightness?

If your battery is in good condition, then there is likely a short somewhere in the main power line (coming from the red lead of your battery).

You should also inspect the MAIN engine power fuse, situated in the Engine fuse box, to ensure it hasn't blown.

Scott

Nov 11, 2009 | 1999 Mitsubishi Galant

1 Answer

The remote is all lit up but it will not turn the aircon on or let me change any thing on the remote


You have not said which model aircon this is, but from the sounds of things your remote sensor board is faulty. This is usually easily changed by removing the front cover (three screws usually have a click cover over each of them and situated behind the louver) The sensor board has a thin wire which plugs into the main pc board. It can only be plugged in one way.

Mar 02, 2009 | Heating & Cooling

1 Answer

HELP! 2000 Chrysler T&C won't go to normal drive?


hi. i have 2002 voyager dissel. i live in laos.
i have problem. i need timebelt setup documet. please help me.

Jan 02, 2009 | 2002 Chrysler Voyager

Not finding what you are looking for?
Panasonic Viera TH-42PX80U Plasma TV Logo

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Televison & Video Experts

 Grubhead
Grubhead

Level 3 Expert

5011 Answers

The Knight
The Knight

Level 3 Expert

73619 Answers

Jaime Hernandez

Level 3 Expert

2315 Answers

Are you a Panasonic Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...