Question about Rado Diastar Classic 300M R12639023 Watch for Men

Open Question

Crwon remove Rado Diastar

How can i remove the crown Rom the Rado Diastar (Automatik from 1973

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: I have a Rado DiaStar

Hears how i do my watch, i have the same watch as you.Just make sure nothing is displayed on the clock face by turning the winder, ie NO digital time, NO daul time, NO alarm, NO stop watch etc, Pull out the winder(crown) and adjust the hands to the time you require by spinning the winder.(Gentley for mins and fast for hours) The digital clock will display wilst doing this, but not change the time.handy if you want to sync both clocks.Push the winder back in at the time to sync and the digital display will go out, then spin the winder again if you want to display the digital features. I hope this helps, please post if it does, Maurice Chevalier- Herts

Posted on Nov 27, 2008

Ad
  • 2 Answers

SOURCE: rado diastar swiss 196-0364-3

I bought the same watch recently and have the same problem. The hours can be adjusted in the dual time zone by looking up the manual, but the minutes stay put. I can't bring them to blink so that these could be adjusted. Any ideas? I sent a mail to Rado through their website but no answer.

Posted on Dec 06, 2009

disap1
  • 98 Answers

SOURCE: how to reduce size on a Rado Diastar wrist watch

That links are most likely ceramic! Take your watch to a reputable watch repair shop...they break very EASY! Make sure they know what they are doing!!!!

Posted on Jan 16, 2010

  • 11800 Answers

SOURCE: Looking for Rado Diastar Anatom watch bracelet

The only source for separate original links is a repair shop that has a defective watch kept for parts. You could order an entire bracelet but that would be very expensive.
The cheapest solution is to get a copy like
http://www.flyingshops.com/rado-anatom-mens-watch-r10365151-4796-p.html
and use its bracelet.

Posted on Jul 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's the price of this watch rado diastar


hi the watch i found is pretty much identical. only thing is anchor is at different angle. points straight down not to the right and its a females watch. price is bout 506 pounds or 895 dollars. hope this is useful to u.

Jan 21, 2013 | Watches

1 Answer

Hi, The first link on my Rado Strap has chipped. Can I get the link replaced without having to replace the whole strap.


Just go to your local service center found on www.rado.com and they will replace the link for you for about $25.

Jun 09, 2011 | Rado DiaStar watch #R20282192 Watch for...

1 Answer

I need new band


If you need a new band for RADO watch, you can pop in any watch shop and choose whichever band you like. The only thing you have to remember is; get the right size. Right size for you watch is the size between lugs in millimetres. Lugs are the things where the band gets attached to the watch. Measure that distance - this is the size of band you are looking for.If you are after original Rado band, then you will have to pop into your nearest Rado dealer shop and order it. The real thing will be far more costly.

Mar 01, 2011 | Rado Diastar Classic 300M R12639023 Watch...

2 Answers

How do i set time and date of my rado wristewhatch?


Hi - I have a Rado Jubilee-Black Face-Lovely Dial
Problem:Time is set with a Key - Back of the watch
I have LOST this Key & need to buy or get one?
Can you please advise - rozilamohamed@yahoo.com
Many Thanks
Ms>Mohamed

Feb 23, 2011 | Rado Diastar Anatom Jubile watch

1 Answer

The release buttons on the clasp of my Rado Jubile wrist watch have lost their spring tension can it be fixed


mcdevito75 here, Best Bet with your Rado watch, Look for a small watch repair shop in your area for adjustment / replacement.

Jun 21, 2010 | Rado Diastar Anatom Jubile watch

1 Answer

Rado diastar swiss 196-0364-3


I bought the same watch recently and have the same problem. The hours can be adjusted in the dual time zone by looking up the manual, but the minutes stay put. I can't bring them to blink so that these could be adjusted. Any ideas? I sent a mail to Rado through their website but no answer.

Jan 06, 2009 | Rado Coupole R22531723 Watch

1 Answer

I have a Rado DiaStar watch (with digital display), and the hands are out of synch with the digital display. Is there a way of adjusting the hands independently of the display? or must it be sent back to...


Hears how i do my watch, i have the same watch as you.Just make sure nothing is displayed on the clock face by turning the winder, ie NO digital time, NO daul time, NO alarm, NO stop watch etc, Pull out the winder(crown) and adjust the hands to the time you require by spinning the winder.(Gentley for mins and fast for hours) The digital clock will display wilst doing this, but not change the time.handy if you want to sync both clocks.Push the winder back in at the time to sync and the digital display will go out, then spin the winder again if you want to display the digital features. I hope this helps, please post if it does, Maurice Chevalier- Herts

Nov 01, 2008 | Rado Diastar Anatom Jubile watch

1 Answer

Rado Diastar


your problem is in setting lever,when the setting lever is jumping the stem cannot get back and lock,you better unscrew the complete barrel drum bridge plate take it out ,and the winding pinion is expose,take the winding gear and the setting lever is expose then arrange the alignment,align the winding pinion to the setting lever,alignment is ok.back bridge plate and screw,,make some winding of the crown,let see rachet wheel can turn transmission wheel of complete barrel drum,if can then checked the stem if already lock.,if lock already the job is done,...email if you some question regarding a watch ;lacarontito@yahoo.com

Jun 17, 2008 | Watches

Not finding what you are looking for?
Rado Diastar Classic 300M R12639023 Watch for Men Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Rado Watches Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18424 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

20927 Answers

ray gallant

Level 3 Expert

52097 Answers

Are you a Rado Watch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...