Question about Washing Machines

1 Answer

Kenmore 110-82477830 washer will not spin water does drain Had a clicking noise SOMEONE overloaded it. any ideas?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

Need a new drain pump

Posted on Jun 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washer won't spin/drain water - no noise, just won't work


might help found my problem was in the motor thought it was in the controls but it came back to motor problems . changed control dial no luck .would think if its a fix yourself try control first. its cheeper than the compressor hope this helps

May 22, 2009 | Kenmore Washing Machines

1 Answer

Model 417.43042200 Kenmore Washer


I HAVE A KENMORE FRONT LOADER WASHER. MODEL 41743042200 AND IT MAKES A NOISE WHEN IN THE SPIN CYCLE, THIS ONLY HAPPENS WHEN SPINNING. CAN SOMEONE HELP

Apr 23, 2009 | Kenmore 45081 Front Load Washer / Dryer

1 Answer

Water does not drain, clicking noise heard no spin cycle


REMOVE DEBRIS FROM PUMP LOCATED INSIDE WASHER ,, REMOVE 2 SCREWS HOLDING BOTTOM PANEL,, PUMP IS PLASTIC TURN COUNTER CLOCK WISE AND REMOVE DEBRIS,, BE CAREFULL HAVE ALOT OF TOWLES STILL HOLD 3 GALLONS OF WATER

Nov 22, 2008 | Kenmore 43142 Front Load Washer

1 Answer

Drum doesn't move or spin


kenmore tumble action washer model#417.44152400,
Washer is approximately 3 years old. Will not drain or spin. When it tries to spin, clicking noise heard inside of unit. Would a clog insie the lines disable the spin cycle ?

Oct 18, 2008 | Kenmore 43142 Front Load Washer

1 Answer

Washplate problem Kenmore Elite Calypso washer


Hello genny2626
Welcome,

You said,your 6 year old Kenmore elite top loader's wash plate doesn't seem to go through its proper motions. When the lid is closed and the washer has filled and the agitating cycle begins, you can hear a vibrating noise as if the plate is trying to move on the gentle cycle, but when the lid is opened, nothing has moved at all. The drain and spin work fine, and the machine goes through an entire cycle without error messages, but the clothes aren't clean. You said, you have heard a lot of horror stories of how expensive these washers are to repair, so would like an idea of what's wrong beforehand.

Here are a list of common vibration noises


Noisy, vibrating, off-balance

 Is the washer level? Does the washer rock when pushed
against the corners?
The washer must be level. The front and rear feet must be in
firm contact with the floor. Check that the locknuts are
tightened. See “Level the Washer.”
 Is the floor flexing, sagging or not level?
Flooring that flexes or is uneven can contribute to noise and
vibration of the washer. A ³⁄₄" (1.9 cm) piece of plywood under
the washer will reduce the sounds. See “Location
Requirements.”
 Is the load balanced?
Evenly distribute the load in the washer basket and make
sure the height of the load does not exceed the top row of
basket holes. See “Starting Your Washer.”
 Do you hear clicking or other noises when the cycle
changes from washing to draining or spinning?
When the drive system shifts or the washer basket settles
between cycles you may hear noises that are different from
your previous washer. These are normal washer noises.
 Is the washer gurgling or humming?

Is the washer level? The wash load
should be balanced and not overloaded. The washer must be
level. The front feet should be properly installed and the nuts
tightened. Reset the rear leveling legs (if needed). See the
Installation Instructions.
Did you completely remove the yellow shipping strap with
cotter pins? See the Installation Instructions.
• Are the gears engaging after the drain and before spin, or
is the upper part of agitator clicking during wash? These
are normal washer noises.

Let me know if any of these are the solution!
Huuum



Oct 13, 2008 | Kenmore Elite HE4 Electric Dryer

1 Answer

Water does not drain, strange noise while in spin cycle


sounds like something is stuck in your drain system. Most likely just in front or even in the pump
Please check this

Apr 22, 2008 | Kenmore 94812 Top Load Stacked Washer /...

3 Answers

Kenmore Washing Machine won't agitate, spin, or drain


The problem sounds like the motor to transmission coupler. If it is not draining or spinning you may find that the lid switch is inop.

Dec 07, 2007 | Washing Machines

2 Answers

Loud clicking noise - wont agitate or spin


I had the same clicking noise. Turned out to be the coupling between the motor and transmission. A $15 plus 1 hour labor fix

Nov 10, 2007 | Kenmore 22422 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Brad Brown

Level 3 Expert

16166 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...