Question about Ford 8n,9n,2n, Tractor Starter With Drive

1 Answer

What is point gap on 9n ford tractor - Ford 8n,9n,2n, Tractor Starter With Drive

Posted by on

  • gomerjt Jun 15, 2009

    thank you for the reply

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 284 Answers

.020

Posted on Jun 15, 2009

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 79 Answers

SOURCE: install distributor points on ford 9n process needed

try this site... http://www.ytmag.com/atrp/specs/ford.htm

Posted on Apr 08, 2009

barterjoe
  • 338 Answers

SOURCE: Ford 9N problems; Changed plugs, wires,

You might check ground. some of these units were ground positive. did you switch the posts?This would cause problems since the electrons are on the inside of the condinser.
Good luck
Joe

Posted on Feb 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Don't know how to read the hydraulic dipstick for a 1944 ford 2n tractor


Ford Tractor Hydraulic System - My Ford Tractors

www.myfordtractors.com/hydraulics.shtml
All N-Series Tractors - Ford-Ferguson 9N, 2N, and Ford 8N ... 6 - How long has it been since you changed the hydraulic fluid? ... If that didn't do it, read on. ... then remove the bottom bolt from the inspection plate that has the hydraulic dip-stick.

Yesterday's Tractors - Fifty Tips for Ford 9N, 2N and 8N ...

www.yesterdaystractors.com/articles/artint268.htm
I'd like to say that the reason I have an 8N Ford tractor is because that's the tractor ... The N tractors have a common sump for the rear end, hydraulic pump andtransmission. ... (Read the label.) .... Take the inspection plate with the dipstick off.

Ford 8N, 9N, 2N, NAA Tractors Information - SSB Tractor ...

www.ssbtractor.com/wwwboard/messages15/
Helpful information and resources on Ford 8N, 9N, 2N, NAA tractors from SSB Tractor, a leading provider of tractor parts, manuals, implements ... 1944 ford 2n: What type of oil to use? and whats the oil pressure should be? ...... N Series Trans/Hydro Fluid - Interesting To Read ... Ford NAA/Jubilee Hydraulic dipstick location?

Jan 01, 2016 | Ford Cars & Trucks

1 Answer

What is the point gap ford 8n


.015 for 2N, 8N & 9N
The 8N also had problems with ignition switch causing several troubles, cheap and easy to replace....Below link is an excellent site.
http://www.yesterdaystractors.com/atrp/specs/ford.htm

May 14, 2014 | Ford 8N Tractor

1 Answer

Ford 9N problems; Changed plugs, wires, cap, rotor, points, and ignition coil. Point gap at .015, new condensor. 6 V battery fully charged. No voltage drop to ignition coil. Results, no spark.


You might check ground. some of these units were ground positive. did you switch the posts?This would cause problems since the electrons are on the inside of the condinser.
Good luck
Joe

Feb 11, 2011 | Ford 8n,9n,2n, Tractor Starter With Drive

3 Answers

Turns over not starting changed points


Verify the point gap is set right and that you are getting a good spark. Check to see if you are getting fuel to the carb.

John

Oct 03, 2009 | Ford 8n,9n,2n, Tractor Starter With Drive

1 Answer

41 9n ford motor not powering up enough


This one sounds like it may still be out of time.

Aug 27, 2009 | Ford 8n,9n,2n, Tractor Starter With Drive

2 Answers

I have a 2n ford tractor. Starts great but will


Hello

Have you Checked the Point Set Gap?
If the Point Set Gap is Not Set Correctly or the Contacts are Burnt, then you will have this Problem.
Please, Do Not Hesitate, If you Hit a Snag or this Does Not Correct the Problem, I am Here if You Require More Assistance.
Hope this Helps. Let me Know What Happens, Please. May the All Mighty Bless You and Yours. Be Safe and Be Happy. Thanks.

Good Luck

Respectfully

jbridger (John)

May 10, 2009 | Ford 8n,9n,2n, Tractor Starter With Drive

Not finding what you are looking for?
Ford 8n,9n,2n,  Tractor Starter With Drive Logo

Related Topics:

1,407 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2478 Answers

donald boissonneault

Level 2 Expert

110 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...