Question about Fisher and Paykel Dryers

Open Question

Error code 151?

No lights on, no ability to turn off or on, it just spins when plugged in and has 151 error code

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Getting a code 151/check engine light, engine runs fine but the transmission wont shift past 2nd gear unless you baby it,any help would be greatly appreciated thanks


Well code 151 is for a problem with one of the O2 sensors in the exhaust pipe. I doubt it would have any affect on the trans.
So you could be dealing with two different problems.

Nov 17, 2015 | Cars & Trucks

2 Answers

When push start button goes right to no spin and turns off


As for unplugging it, I had an issue with mine not spinning on the Perm Press cycle. I tried unplugging it for an hour and plugging it in again to no avail. Just gave up on the Perm Press cycle. A few months later I unplugged it for a week while I was on vacation and low and behold, it started to spin on the Perm Press cycle! I'm not sure how long it would have needed to be unplugged, but you may want to try for a couple of days. But, in the mean time....

Try running the diagnosis and looking for an error code.
To recall an error code,
• Wake the machine by pressing any button
• Wait 5 seconds
• Press and hold the Start and Pause Cancel buttons simultaneously
• All LEDs will go blank and after a few seconds the control will signal the stored code using audible beeps and blinking LEDs. The control will repeatedly signal the code, as long as the Start and Pause Cancel buttons are pressed. A two-second pause between repeats affords you the ability to make accurate counts to identify the correct error codes.
For complete instructions and to run a more thorough diagnosis, download the instructions here:
http://manuals.frigidaire.com/prodinfo_pdf/webster/134542000.pdf

May 10, 2015 | Frigidaire GLTF2940ES Front Load Washer

2 Answers

Hi, How Can I Reset error in my wash machine Bosch


You can reset the error code by the follow steps.
Turn the knob to the off or reset position, 12 o'clock.
Turn the knob to the 6 o'clock position.
Press and hold the spin button and while holding the spin button turn the knob to the 7 o'clock position.
Continue holding the spin button for about 5 seconds then release the spin button and now turn the knob to off
When your turn it back on it should have cleared the error code.

Sep 26, 2013 | Bosch Washing Machines

1 Answer

Model Gw709AU


When you start your machine is the water just go stop go stop,
Just wait for the machine to display an error code on the wash progress lights and beeps constantly.
It could be the Rotor Position Sensor, out of balance switch or lid magnetic reed switch.
Your error code will determine this.
Is your machine beeping & showing a weird pattern of lights on the wash cycle, It is displaying an error code,
To read this error code you start at the red spin light & work to the left only add up the lights that are on. Red spin light = 1 2nd rinse light =2 1st rinse light =4 last wash light=8 4th wash light=16 3rd wash light=32 2nd wash light=64 1st wash light=128
j8paojvh5jrgaaaaabjru5erkjggg==


2_26_2013_3_17_31_am.jpg

Feb 20, 2013 | Fisher and Paykel Washing Machines

1 Answer

LE LIGHT IS APPEAR


Over-sudsing is the main cause of LE error codes. Using non-HE (high efficiency) detergents or too much detergent will cause stress on the motor. In addition, detergent residue can also cause leaking and odor. Follow these steps to resolved an LE error code caused by over-sudsing.

Step 1: Unplug the washer and allow the unit to sit for 30 minutes to give the suds time to dissolve.

Step 2: Plug the washer back in and press [Power] to turn on the washer.

Step 3: Do not choose a washing cycle. Press the [Spin Speed] key until "No Spin" is selected.

Step 4: Press [Start/Pause] to begin a drain only cycle.

Step 5: After the drain only cycle has completed, remove the clothing items from the machine. Turn the power back on and select [Rinse and Spin] and then press [Start/Pause]. This will remove excess soap suds and light residue from the drum. Repeat this step until no visible suds are in the drum of the washer.

Nov 12, 2012 | Washing Machines

2 Answers

I've got an LE code on the front of my washer


This error can sometimes present because of a miscommunication between the control panel and the wash motor. In this instance, the washer simply needs to be reset.

Step 1: Unplug the washing machine.
Step 2: While the washer remains unplugged, press and hold the [Start/Pause] button on the front panel for 5 seconds.
Step 3: Plug the unit back in, and run a rinse and spin cycle to test if the LE code is cleared.

Are there soap suds visible in the drum?
Over-sudsing is the main cause of LE error codes. Using non-HE (high efficiency) detergents or too much detergent will cause stress on the motor. In addition, detergent residue can also cause leaking and odor. Follow these steps to resolved an LE error code caused by over-sudsing.

Step 1: Unplug the washer and allow the unit to sit for 30 minutes to give the suds time to dissolve.
Step 2: Plug the washer back in and press [Power] to turn on the washer.
Step 3: Do not choose a washing cycle. Press the [Spin Speed] key until "No Spin" is selected.
Step 4: Press [Start/Pause] to begin a drain only cycle.
Step 5: After the drain only cycle has completed, remove the clothing items from the machine. Turn the power back on and select [Rinse and Spin] and then press [Start/Pause]. This will remove excess soap suds and light residue from the drum. Repeat this step until no visible suds are in the drum of the washer.


Hope this helps.

Jul 06, 2011 | LG WM2301HW Front Load Washer

1 Answer

I've gotten the error code DL and then F, I tried sanding, unplugging but it still shows me the error. How can I fix it?


Hi,
Initially unplug the washing machine.While the washer remains unplugged, press and hold the [Start/Pause] button on the front panel for five seconds.
Plug the unit back in, and run a rinse and spin cycle to test if the DL code is cleared.

If you still face the problem then follow the procedure:

Unplug the washer and allow the unit to sit for 30 minutes to give the suds time to dissolve.

Plug the washer back in and press [Power] to turn on the washer.

Do not choose a washing cycle. Press the [Spin Speed] key until "No Spin" is selected.

Press [Start/Pause] to begin a drain only cycle.

After the drain only cycle has completed, remove the clothing items from the machine. Turn the power back on and select [Rinse and Spin] and then press [Start/Pause].
This will remove excess soap suds and light residue from the drum.

Repeat this step until no visible suds are in the drum of the washer.


Hope this helps.

Shane

Mar 15, 2011 | Kenmore Elite 45986 Front Load Washer

1 Answer

My washing machine is cannot spin ,it show error code LE


Over-sudsing is the main cause of LE error codes. Using non-HE (high efficiency) detergents or too much detergent will cause stress on the motor. In addition, detergent residue can also cause leaking and odor. Follow these steps to resolved an LE error code caused by over-sudsing.
Step 1: Unplug the washer and allow the unit to sit for 30 minutes to give the suds time to dissolve.
Step 2: Plug the washer back in and press [Power] to turn on the washer.
Step 3: Do not choose a washing cycle. Press the [Spin Speed] key until "No Spin" is selected.
Step 4: Press [Start/Pause] to begin a drain only cycle.
Step 5: After the drain only cycle has completed, remove the clothing items from the machine. Turn the power back on and select [Rinse and Spin] and then press [Start/Pause]. This will remove excess soap suds and light residue from the drum. Repeat this step until no visible suds are in the drum of the washer.

Nov 28, 2010 | Washing Machines

1 Answer

My KitchenAid dishwasher will not run. Start light is blinking


Make sure the controls are not locked. Some units have the ability to lock the controls so that kids cannot turn on the dishwaher. You can also try unpugging the power to the unit from under the sink for about 10 minutes and then plug it back in. This may reset the control board if it has a fault and stopped from error code.

Sep 26, 2009 | KitchenAid 24 in. KUDI01FLSS Stainless...

Not finding what you are looking for?

Open Questions:

Dryers Logo

Related Topics:

671 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Tim Whalen

Level 3 Expert

3074 Answers

Bill Eager

Level 3 Expert

429 Answers

Are you a Fisher and Paykel Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...