Question about Maytag Bravos MTW6600T Top Load Washer

1 Answer

My Maytag washer Model # MTW6600TQ0 will not drain or spin it only hums, what could the problem be?

It went through almost entire cycle then when it go to spin cycle it started beeping then just humming and the water would not drain so it did not spin.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 283 Answers

Weak windings? You call yourself a tech?

Posted on Mar 24, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 96 Answers

SOURCE: Won't Run

The humming usually means the motor is trying to start but can't either because of weak windings or not enough electrical power. Need to check the motor control.

Posted on Mar 02, 2008

JR JR
  • 116 Answers

SOURCE: Maytag washer wont start spin cycle...

INSPECT YOUR PUMP HUMMING NOISE USUALLY PUMP MOTOR ARE PRETTY RELAIBLE

Posted on Nov 30, 2008

  • 1 Answer

SOURCE: Maytag Atlantis Washer, model MDG6200AWW

I just hooked up my washer and after filling it the motor hummed and smelt like it was starting to burn! Is this a fixable problem?

Posted on Jan 04, 2009

  • 1 Answer

SOURCE: Maytag washer wont start after it fills

Did you replace the pressure switch its a round plastic thing with a plastic tube at the bottom and six electrical connections

Posted on Mar 14, 2009

  • 219 Answers

SOURCE: LAT9604AAE No agitation but drum spins and drains water

cold possibly be just the agaitor but odds are u need a transmisson not worth repair

Posted on May 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Maytag legacy series washer


The drive motor which spins the drum is connected to the drum by a rubber belt. Sounds like the belt is burned through. Make sure you can spin the inside tub by hand to verify that the tub can turn freely before you replace the belt. The hum is from the drive motor just spinning freely.

Sep 02, 2016 | Maytag Legacy Series Top Load Washer

1 Answer

Where is the fuse located at


if the pump is making noise the thermal limiter is ok, there is no fuse as such, most likely the motor speed control circuit board has burned out, it is a known defect in this washer.

Mar 17, 2010 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Will not do final spin cycle leaving clothes


Your drain pump has something lodged in it. Remove drain motor, open it up and inspect for obstruction. remove it then reassemble.retrywashing cycle.

Nov 12, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Washer will not pump out water.


drain pump restricted with debree or drain pump bad. if you can hear drain pump humming during drain function then clean out and see what happens

Jun 22, 2009 | Washing Machines

2 Answers

Loud during the spin cycle.


would suspect something in the drain pump rather then something witht he tub, tip unit back and check for debrisin right hand side pump

Mar 25, 2009 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

GE top load washer won't drain or spin


there was something stuck in the water pump. we pulled it out and good to go.

Jun 14, 2008 | Washing Machines

1 Answer

Won't Run


The humming usually means the motor is trying to start but can't either because of weak windings or not enough electrical power. Need to check the motor control.

Mar 01, 2008 | Maytag Neptune MAH5500B Front Load Washer

3 Answers

Wont spin or drain


The drain pump is jammed or clogged up. Remove the filter cover and check for bobby pins, coins or bra wires. If clean, remove drum to pump hose from the pump and check for any foreign matter. Try to turn the pump impeller by hand. It should turn freely. If pump is not free, replace it.

Nov 03, 2007 | Maytag Neptune MAH5500B Front Load Washer

Not finding what you are looking for?
Maytag Bravos MTW6600T Top Load Washer Logo

230 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...