Question about Samsung 7.3 Cu. Ft. Electric Dryer

1 Answer

I am trying to replace the belt on my front load Samsung dryer model dv419aew/xaa

Replacing the belt

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 446 Answers

You will need to pull the top to gain acces to the control panel which you will remove to get to the screws on the front and go from there

Posted on Mar 24, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 41 Answers

SOURCE: Re: Samsung DV4015J Dryer Belt Replacement


See:
http://www.fixya.com/support/t1210394-samsung_dv4006_dryer_belt

Posted on Jul 01, 2009

  • 382 Answers

SOURCE: how do i fix a belt that slipped off my samsung

There is a tensioner in the pulley that should keep the belt from slipping off.n most cases they work very well at keeping the belt tight.In your case the belt may be stretched too much ,I would check it and replace it if necessary

Posted on Mar 07, 2010

  • 3 Answers

SOURCE: replacing belt in samsung dryer I cant get the

This photo is from a Samsung DV409AEW, but I assume they are quite likely the same.
If they are the same route the belt per the photo below. It is counter-intuitive that the spring pulls the arm down, rather than to the left. Hopefully this will be your issue.
Hope this helps!
helping_hans.jpg

Posted on Dec 01, 2010

  • 291 Answers

SOURCE: have a samsung dryer model DV209AEW/XAA. I "hand

Check to make sure your child lock is off first. Hold the time and signal buttons simultaneously for three seconds. Unlikely, but do check. Some of these dryers have a safety switch that the idler pulley has to engage to allow the dryer to run. I tried to find a schematic for this model but could not get one to tell if you do have a safety switch. Look at the arm of the idler pulley and see if it is contacting the switch actuator correctly. When a belt breaks or pops off, sometimes the arm of the pulley will move to the other side of the switch actuator and will not allow the dryer to run once a belt is reistalled. I would also look to see if a wire was knocked off of the motor switch when your belt came off. Good Luck, Appliance Specialists

Posted on Dec 03, 2010

  • 608 Answers

SOURCE: My Samsung dryer Model #DV448AEP/XAA

I think your heating element is burned out. You can find parts at repairclinic.com

If you remove the element (unplug it first of course) you will be able to tell if it is burned out by looking at the actual heating coils. If there are any breaks in the wire anywhere you know its the problem.

Good luck

Posted on Dec 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I own a Samsung dryer model DV218AEB/XAA. In both the sensor and timed cycles it shuts off early and goes dead for about 30 minutes before it comes back to life and the load can be restarted, only to


Hello,
I have a good idea that it may be the following;

Drum Roller Axle

This dryer has drum support rollers. There will always be two supporting the rear of the drum, and on some models there may be two supporting the front of the drum. The rollers must spin freely to work properly. If the roller axles are worn out the rollers may not spin freely which can overload the motor and the dryer stops. If the dryer stops mid-cycle, remove the belt and spin the drum, it should spin freely. If not, check the rollers and roller shafts.
You can check out other possibilities and order parts here using the following link;
http://www.repairclinic.com/RepairHelp/How-To-Fix-A-Dryer/2---/Dryer-stops-turning-during-cycle

Good Luck!
Rich Lilja

Oct 29, 2014 | Samsung DV218AEB/XAA 7.3-CuFt Electric...

1 Answer

Samsung dryer DV419AEW/XAA belt parts number and how to replace?


You can find helpful exploded view diagrams and order parts by entering your part number or the full model number from the tag on the oven here.

Dec 28, 2013 | Samsung 7.3 Cu. Ft. Electric Dryer

1 Answer

Samsung Dryer Model DV419AEW /XAA Dryer will not


I doubt its the main board. Try seeing if the drum is tight and seeing if the belt broke by spinning it by hand. If the drum is real sloppy and you can't feel motor tension, you need a belt. I would rule out the mainboard until last because the belt is like 89 cents.

http://www.amazon.com/341241-Whirlpool-Kenmore-Dryer-Belt/dp/B00064NH6E

http://www.youtube.com/watch?v=zNATJ8qyqP4




Sep 27, 2013 | Samsung Clothes Dryer Control Panel Main...

1 Answer

Model dv209aewxaa timer counts down but nothing else is runing


Belt came off?? see We fixed our dryer!! so happy!! First We ordered the dryer belt with part # Samsung Dryer Belt 66002-001655. I got it off Amazon at a good price $11-13 at http://www.amazon.com/gp/product/B001KGX...THANK GOD we ordered it just in case because it turned out the belt had NOT slipped off but was SHREDDED apart. The BEST ADVICE to this particular model Samsung VRT steam dryer DV419AEW came from a commenter to another thread . Follow this thread if you have Samsung VRT steam dryer with model # DV419AEW= this threadhttp://www.fixya.com/support/t1210394-sa... The comment at the BOTTOM of the reply made by "dumb-stump". He describes how you take apart this particlar model. I also watched the youtube video on belt placement http://www.youtube.com/watch?v=obaoSDbzY... This shows how to place on pulleys etc once you get belt around the drum.

Jan 29, 2013 | Samsung Dryers

1 Answer

Samsung dv419aew/xaa turns on but drum does not turn, Belt is good and drum retates easy by hand


Can you hear the motor running at all? Do you feel any heat?

Jan 28, 2013 | Dryers

1 Answer

Samsung dv210 will not turn


Belt come off/damaged? Same thing happened to us and the clicking noise was our shredded belt flapping around hitting the drum. see : We fixed our dryer!! so happy!! First We ordered the dryer belt with part # Samsung Dryer Belt 66002-001655. I got it off Amazon at a good price $11-13 at http://www.amazon.com/gp/product/B001KGX...THANK GOD we ordered it just in case because it turned out the belt had NOT slipped off but was SHREDDED apart. The BEST ADVICE to this particular model Samsung VRT steam dryer DV419AEW came from a commenter to another thread . Follow this thread if you have Samsung VRT steam dryer with model # DV419AEW= this threadhttp://www.fixya.com/support/t1210394-sa... The comment at the BOTTOM of the reply made by "dumb-stump". He describes how you take apart this particlar model. I also watched the youtube video on belt placement http://www.youtube.com/watch?v=obaoSDbzY... This shows how to place on pulleys etc once you get belt around the drum.

Jan 20, 2013 | Samsung 7.3 Cu. Ft. Electric Dryer

Not finding what you are looking for?
Samsung 7.3 Cu. Ft. Electric Dryer Logo

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Dryers Experts

Tim Whalen

Level 3 Expert

3074 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Are you a Samsung Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...