Question about HP PSC 1315 All-In-One InkJet Printer

2 Answers

Reset 1310

Is always in ERROR mode even whe i desconnect it when i connecte it marks the same thanks!!!!

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

HP PSC 1310 "hard reset" is easiest try:
power on, wait until the power cycle completes. WITHOUT switching off, unplug power cord from printer. Wait approcimately 30 secs, plug back in and power on. This is a "dirty power up" and causes a reset that does NOT reset your settings.

if that fails, try a FACTORY reset:

  1. With the power on, disconnect the power cord from the rear of printer.
  2. Wait 15 seconds.
  3. Reconnect the power cord to the rear of the product.
  4. When the lights begin to blink, press and hold both the On/Resume button (Power ) and the Paper Size button at the same time.
  5. When only the On/Resume button (Power ) is blinking, release both buttons.
  6. Wait until the On/Resume button (Power ). is steady.
Factory reset (settings wiped) is done. Try setting it up again.

if all else fails, here is a guide that may help:

http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/kb/docDisplay/?spf_p.tpst=kbDocDisplay&spf_p.prp_kbDocDisplay=wsrp-navigationalState%3DdocId%253Demr_na-c00095908-36%257CdocLocale%253D%257CcalledBy%253D&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

Good luck!

Posted on Mar 26, 2014

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Do you get the error when just connecting the power, and not the USB cable?

Leave the power disconnected for an hour or so, then reconnect (not the USB - leave that disconnected).

Posted on Mar 24, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to clear error code from my copier?


turn it off at the wall
start again

if error still there need more information to help
what model cannon copier

Sep 03, 2016 | Canon Office Equipment & Supplies

1 Answer

I have a D-Link WBR-1310 router. It worked fine on Thursday evening. Now my laptop and my TIVO cannot even detect the router. I have tried resetting it and even unplugging the router and plugging it...


I suggest you RESET the D-Link back to the default setting and configure the wireless settings again.
To reset the D-Link back to the default settings -
Press and hold the RESET button at the back of the router with the power ONuntil the LEDs flash at the time the release the RESET button.
Connect a LAN cable from the D-Link to your laptop/computer's LAN port, openthe browser on your laptop/computer and enter the D-Link's configuration URL..
http://192.168.0.1
The default login = admin
The default PW = blank (just press Enter) You can now change the default password.
You can now configure the wireless settings. Now configure the wireless card in your computer/laptop withthe router's wireless settings.
To secure your wireless network from unauthorized access,please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

Jun 18, 2011 | D-Link 802.11g Wireless Router WBR-1310...

1 Answer

Error 103


Press in and hold the reset button on the back of the router. Connect directly with a patch cable and configure your wireless settings by typing 192.168.0.1 in address bar. Download the manual here:
http://www.dlink.com/products/?tab=3&pid=WBR-1310&rev=WBR-1310

Mar 08, 2010 | D-Link 802.11g Wireless Router WBR-1310...

1 Answer

I just bought a new hp laptop and when I try to connect to my D link 1310 wireless router it says that my key in not valid. I am typing in the right encryption key and it's say that I need a to use a 5 or...


Hi smithcontrac,

The reason your getting that 5 to 13 letter key is that you must of set it up under WPA incription. What I would do, is log back into the router, and reset to WEP and re-enter your key to assign it correctly. And don't forget to write down what it gives you back as a new key.

Good Luck,

And don't forget to leave a rating,

Thanks

Mark

Oct 11, 2009 | D-Link 802.11g Wireless Router WBR-1310...

3 Answers

I forgot the username of dlink wbr-1310 wireless router


Hi there,

As an initial info try to do a hard reset on the unit, this process will restore the system into a original settings. you can find the reset switch on either on the left of right sight of your router.

or

you may visit this SITE to recover again your current password without erasing or removing the current settings made.

Reset Password.

Hope this idea helps you.

Thank you for using fixya.

Nov 20, 2008 | D-Link 802.11g Wireless Router WBR-1310...

1 Answer

Canon IR 1310 Copier


I have downloaded service manuals, parts manuals, maintenance manuals, service mode, error codes from www.printcopy.info

Sep 13, 2008 | Canon Office Equipment & Supplies

1 Answer

Unable to connect to the internet


Mike, Try setting up a new connection in Internet Options in Control Panel. Please let me know how this works for you.
thanks

Jan 24, 2008 | D-Link 802.11g Wireless Router WBR-1310...

6 Answers

How do I secure my dlink wireless connection?


Type 192.168.0.1 (you can type the router address if you have changed) and enter on browser's addressbar. Router's interface will appear.
Click on SETUP and Click on the WIRELESS SETTINGS at left side. on the page you will see the option of WIRELESS SECURITY by drop down menu you can choose the Security mode that you wish. here is the link for the emulator
http://support.dlink.com/emulators/wbr1310_revB/wireless.htm

Please post your question if you need further assistance
Good Luck

Jan 19, 2008 | D-Link 802.11g Wireless Router WBR-1310...

2 Answers

W300i Transfer Error


Unplug phone from any connections. Remove battery, Keep power button pressed for 30 seconds. Insert battery, Turn on phone.

Sep 27, 2007 | Cell Phones

Not finding what you are looking for?
HP PSC 1315 All-In-One InkJet Printer Logo

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Seeker5211
Seeker5211

Level 3 Expert

1089 Answers

kakima

Level 3 Expert

102366 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...