Question about Crafts & Hobbies

1 Answer

Bachman S-4 stops and starts

Nedd to rewire engine

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 30 Answers

Check the electrical pick-ups first. Be sure they are clean and bright. Don't use sandpaper or steel wool for cleaning! An ink eraser or rubber track cleaning block (large ink eraser) is best.

Posted on May 06, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Larry.bachman@aol.com


no there is not. there is a fuse, relay and resistor that could cause it to stop running

Mar 15, 2014 | 1996 Pontiac Grand Prix

1 Answer

Driver Wheels are not aligned properly. Will not run in reverse without de-railing.


Best best is to send it back to the parts & service department, they will either repair it or replace it. It should have a lifetime warrantyif you are the original owne If not under warranty, I believe the charge is $35.00 for repair/replacement.But check with parts & service.

http://www.bachmanntrains.com/home-usa/prod_serv.php



link is to Bachmann Parts & Service.

Apr 10, 2012 | Bachmann HO Scale Classic Collector Series...

1 Answer

Clicking sound then when it stop the check engine light come on. it will not start until the clicking sound stop. previous owner rewired the truck and add a sound system including a big speaker


Your jeep ecu needs to be repaired. You have what is known as the 'No Check Engine Light" no start relay clicking problem. Have the ecu either repaired (a lot cheaper) or replaced. That will eliminate the delayed check engine light and wait time to start.

Feb 17, 2011 | 1994 Jeep Grand Cherokee

1 Answer

I need to know how to rewire the ignition system


Hi and welcome to FixYa,

On your requirement to "...rewire the ignition system..." of an XS650, below basic ignitor wiring scheme maybe of reference:
  • white / red - from pick up;
  • white / green - from pick up;
  • black / white - from pick up;
  • orange - to ignition coil;
  • red / white - IGN + 12 from engine stop switch ;
  • black - ground;

Good luck and thank you for asking FixYa.

Nov 14, 2009 | 1980 Yamaha XS 650 G

1 Answer

I nedd diagram


Check inside the control panel for a service manual.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Jun 16, 2009 | Kenmore 3.2 cu. ft. Plus Top Load Washer

2 Answers

ENGINE DOES NOT MOVE VERY WELL AND IS LOUD


Sounds like the wheels may be dirty on the one . Have you tried cleaning them? The noisey one may need a little grease on the gears. The one that does not move but lights up, not sure. Have you tried to take the body off and see if a wire is disconnected?
Try going on line and look for a group on Yahoo Groups for N-scale. They will probably be more helpful and you will get more information about N scale trains. Good luck!
Bob D.

Dec 12, 2008 | Seth Thomas Bachman Thomas Annie Clarabel...

1 Answer

No power until key is on


ok it seems as though the car has been rewired in someway that everything runs off the acc power maybe prvious owner rewired it?

Oct 03, 2008 | 2002 Mitsubishi Galant

1 Answer

Carbourater for a tecumseh engine


start by closing jets (clockwise). Then turn jets 1 full turn counterclockwise. this should get engine started. Then adjust jets left or right to fine tune,until engine starts running smoothly.

Aug 06, 2008 | Grilling

Not finding what you are looking for?
Crafts & Hobbies Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Crafts & Hobbies Experts

R.A. Ellis
R.A. Ellis

Level 3 Expert

8899 Answers

Debbie

Level 3 Expert

1860 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Craft and Hobby Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...