Question about Bosch WET 2820 Front Load Washer / Dryer

Open Question

Program start to run then stops after a short time

I was running a coloured cotton 40 program, it filled with water and detergent ran into machine, I have manage to get the washing out, cleaned suds pump as per manual. Then tried to run program with machine empty it runs for a short time then stops and will not continue. Main wash light remains on, fills with water, drum turns 4 times then changes direction for 2 turn then stops. I have turned to off using the program selecter, then when it clicks to release the door, selected spin program (spin light on only) which drains the water out, drum does about 4 rotations then stops.

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When my Maytag bravos washer starts to wash cycle it stops with an F 51 code. it dose it every time it agates


Cause: suds. The wrong detergent or the wrong amount of detergent, makes the motor overheat.
Why? In my opinion when suds are detected the program needs to make them go away for fear the clothes won't be clean. So the program makes the motor do extra work to try and fix the problem. The poor washer motor gets worked to death because the water ain't right. This washer is designed to work with a small amount of water. Only a tiny amount of soap is needed to do the job. Put a cup of detergent in there and the machine is gonna constantly run way past time to be done just to get rid of the detergent. This causes the machine to overwork the motor and destroy the rotor position sensor.

Feb 04, 2011 | Maytag Bravos MTW6600T Top Load Washer

1 Answer

Error code E:13 on my 500 plus series washer


Hi,
The E13 error code on your Bosch washer refer to a drainage problem or the pump time might have been exceeded
Either it might be due to a clogged pump, improper detergent being used, ( must use "HE" detergent ) hence suds not allowing a proper drain cycle. You should clean water drainage pipe and/or drain hose. Turn selector to off and restart 'drain, program or, on 500 plus machines, the 'refresh' program. It also says this is caused by using too much detergent. Bosch recommends using half of what the manufacturer recommends when using HE detergents. They don't recommend regular detergents. First run the short wash or refresh cycle without detergent and hopefully your lines will clear.

Thank you !!

May 25, 2010 | Bosch 3.81 cu ft WFMC530 1UC Nexxt 500...

1 Answer

Year old Bosch SHU33A0UC won't start. Lights on


Light's on mean you have power.

Initiate the self test program by doing the following -

To start test program, press and hold both POWER SCRUB PLUS and RINSE & HOLD program buttons, then turn unit on
by pressing ON/OFF button. When program buttons are released, lights above them will flash. To end test program, press
ON/OFF button.
To check program indicator lights (POWER SCRUB PLUS, REGULAR WASH and RINSE & HOLD), press and hold each
program button. When REGULAR WASH program button is pressed, CLEAN light also comes on.
To start testing, press both POWER SCRUB PLUS and RINSE & HOLD buttons a second time. When testing has ended
and a fault was detected, the following indicator lights will be lit:
POWER SCRUB PLUS = Heater fault
REGULAR WASH = Water filling fault (over or under filling)
RINSE & HOLD = NTC (temperature sensor) fault – note circulation motor stops shortly after it started
during an NTC fault
To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil,
measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays
at ~ 1.5-2 A, then heater, high limit or flow switch are faulty.
If water level switch (f1) has failed (opened), REGULAR WASH light will come on and unit will continually fill and drain
where testing won't be completed. If flow switch (e5) has failed (opened), water won't heat (to 150ºF) and water won’t stop
circulating. If NTC probe (f2/f4) has failed (opened), RINSE & HOLD light will come on immediately and testing will end
shortly after water has started circulating.
If more than one fault occurs, more than one light will be lit.

Let me know what you figure out. I can repair these boards most of the time.

Dec 18, 2009 | Bosch 24 in. SHE44C02UC / SHE44C06UC /...

1 Answer

Exactly the Same Problem


It's difficult to say without seeing the machine or having a failure code.
The machine looks for a switch to close as it fills with water. Maybe a pressure switch?
You could find the switch and see if it clicks when blowing into it and even test it with a meter.
That's an easy test.
Maybe the module has failed.
Hope it's given you something to look for.
regards
john

Aug 28, 2009 | Zanussi ZWD12270 Front Load Washer / Dryer

1 Answer

Wrecking our clothes!!!


Check the water temperature - it may be filling with HOT only.
If this is the case - replace the dual inlet water fill valve.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

May 30, 2009 | Washing Machines

1 Answer

Water goes thru fabric softener dispenser not soap dispenser!


Yes you will need a service call, you may have a issue with the water valve or control, At the start of the cycle it should not be filling the softener dispenser till later in the program.

Jan 10, 2009 | Kenmore 42822 Front Load Washer

1 Answer

Drum not filling up with water, it's draining straight out.


That means that the drain pump is always on.
That can happen because of a faulty or stuck water level switch (the one with floating sensor), because of a faulty drain pump solenoid, or because of a faulty pump.




Oct 24, 2008 | Washing Machines

2 Answers

I ran the test program and found faults


No you will need to check the motor controller board

Nov 21, 2007 | GE WBVH6240F Front Load Washer

Not finding what you are looking for?

Open Questions:

See all Bosch WET 2820 Front Load Washer / Dryer Questions

Bosch WET 2820 Front Load Washer / Dryer Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Washing Machines Experts

Tim Whalen

Level 3 Expert

3072 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...