Question about Jenn-Air 36 in. CCG2523 Gas Cooktop

1 Answer

Flame flares up sporadically while cooking

Have a gas Jenn Air cooktop where the flame flares up sporadically normally while cooking on that particular eye.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Jenn-Air Master
  • 842 Answers

Hi,

Due this test, turn on all burners on high, as you turn them on, does the problem burner change in volume or size of flame? If all burners are on and you only have issues with that single burner you need to replace that burner valve only. If you have issues with all burners when the all are on, replace the regulator.

I hope this helps and leads you in the right direction.

Posted on Apr 02, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

fridgetech
  • 473 Answers

SOURCE: Jenn Air Cooktop Burners Won't Ignite

The orifices may be dirty. They can usually be cleaned out with a safety pin.

Posted on Oct 05, 2007

  • 2 Answers

SOURCE: Jenn-Air Gas Cooktop Model CVGX2423

Just had this problem today on our seven or eight year old Jenn-Air cooktop. When using the front right burner all ignitors would continue to fire until I turned off the burner. The three other burners worked correctly. After trying all the obvious soulutions w/o success I pulled off that burners control knob and the rubber seal which exposed the valve. Their was a bunch of crud in there. I put a small (one inch) paint brush in there and vigorusly loosened all the crud. I then inserted the nozzle of our central vac - which just happened to fit perfectly - and sucked all the stuff out. I repeated the proceedure a couple more times, reassembled the knob and started the burner. Worked just perfectly!!! YMMV. Good luck.

Posted on Feb 08, 2008

  • 1 Answer

SOURCE: Jenn-Air JGD8130 Gas Cooktop will not ignite

I just ordered one of these---sounds like people are not happy with this model---please get me more info

Posted on Mar 29, 2008

  • 1 Answer

SOURCE: cooktop fan switch replacement

1. Turn off the power at the breaker box.
2. lift off the air grill.
3. remove the two screws at the front of the control switch panel (escutcheon)..
4. slide the control panel forward until it disengages, then lift up to expose the switch assembly and wiring.

Posted on Jun 18, 2008

mgprice
  • 744 Answers

SOURCE: Gas Jenn Air Cooktop Issue with Electric Starter

Did you spill water near/on knobs? if so leave to dry out for 24 hours. If still clicking after 24 hours one of the switches has shorted out and needs to be replaced. You can find which one with a multi meter/condinuity test. Hope this helps...Good Luck

Posted on Jun 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

One of the burners does not light but it does have a spark at ignitor but it is not directed to burner port


Be certain the openings in the burner are free of debris. Boilovers can leave debris in the openings that will harden. Once this happens you cannot get the right mix of oxygen and gas for a flame to ignite. With the burner OFF, you can clean the openings gently with a toothpick to loosen the cooked on "gook." Then when you turn on the burner, the flame should burn off the residue and your range will be "cooking on all four burners!"

Nov 06, 2010 | Jenn-Air JGC8536 Gas Cooktop

1 Answer

1 burner flares and sputters


Hello. Chances are that something on the stove boiled over or got poured into that burner. take it off, soak it overnight in water with dishsoap added, then rinse it and let it dry before reinstalling it. Repeat the soaking in soapy water if necessary until the flaring, sputtering and black soot is gone. regards, Joe

Dec 14, 2009 | Jenn-Air 34 in. Expressions CVGX2423 Gas...

1 Answer

Do i caulk around my jenn air cooktop?


hello I assume you mean you are installing a new cook top, You can use caulk but its not easy to clean up after. Normally when I install a new cook top I use plumbers putty to seal it and bed it in. Hope this helps! Mike

Oct 27, 2009 | Jenn-Air JED8430 Electric Cooktop

1 Answer

Hello. When I turn on a burner, another one


they will all click when lighting,
if this is happening after ignition, turn your flame just a bit higher, your loosing flame ground

Oct 03, 2009 | Jenn-Air JGD8130 Gas Cooktop

1 Answer

How to start the self-cleaning cycle in jenn-air sce30600?


An electric cooktop uses a great deal more electrical energy than a gas cooktop. The electric portion of the gas cooktop runs the electronics (clock, timer, ignitor, oven light, etc.), and these are small electrical loads. An electric cooktop uses more electrical energy cooking a batch of, say, pasta sauce, than a gas cooktop would normally use in a month or two. There just isn't a good comparison as there is such a broad difference in the electrical usage of the two units.

Sep 20, 2009 | Cooktops

1 Answer

Flames too high Jenn-air CCG2423


Definitely cut your loses and get a cooktop with a warranty. That unit sat on the back shelf for a reason.......it didn't work properly.

Also, but a cook top that is compatible with the safety knobs they sell as child guards at places like lowes and home depot.

here is a link to show you how the child proof knobs work
http://www.associatedcontent.com/article/327577/childproof_your_stove_safety_1st_stove.html

Jun 20, 2009 | Jenn-Air 30 in. CCG2423 Gas Cooktop

1 Answer

Spark module will not stop after lighting burner


The module might not sense the flame: check electrical connections: wire (and its contacts0 and conections by fryer chasis; to be sure please bond with 18AWG wire pilot burner with spark module green wire.
MarKor

Mar 09, 2009 | Jenn-Air 30 in.JGD8430ADS Gas Cooktop

1 Answer

Jenn air jgc9536


yes , but that could be the manufacturers design or the wrong knobs

Oct 18, 2008 | Jenn-Air 35 in. JGC9536 Gas Cooktop

1 Answer

Burners/Heat


make sure you have the correct orifices, make sure you have good gas pressure and make sure pressure regulator is ok.
also if the unit has been in service for a while check the orifice for build up a wire or needle will work to knock out any build up

Apr 23, 2008 | Jenn-Air JGD8130 Gas Cooktop

Not finding what you are looking for?
Jenn-Air 36 in. CCG2523 Gas Cooktop Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jenn-Air Cooktops Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

paulcarew

Level 3 Expert

2458 Answers

Are you a Jenn-Air Cooktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...