Question about Korg X5d

Open Question

Pitch Wheel I can't figure out how to change my pitch wheel settings in combination mode. I want to have it go a FULL OCTAVE up and down, but I've studied the manual and can't figure out how to do it.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sounding a half step too high


Use the factory reset
Hold down highest white key whilst turning on
This should return to factory settings - pitch should now be back at A440
If you need to adjust then see page 19 of the user manual where it explains fine tuning.

Mar 14, 2015 | Yamaha P95 Digital Piano

1 Answer

I tune my guitars at 400 using a clip on tuner,which I believe is concert pitch I've recently bought a 5 string blue grass banjo .I set tuner to c mode to tune banjo is this correct


Actually, concert pitch is A=440 rather than A=400. Normally a 5 string banjo is tuned G (octave) D G B D though many variations exist.

Feb 20, 2015 | Ovation Music

1 Answer

How to tune 12 string guitar with ga40


Just use as if you are doing a 6 string ( instructions in the pack ) only play one string in each group at a time. The thinner string in a pair should be exactly one octave higher than the thicker string. Strings of the same thickness are in unison ( sound the same pitch )

Nov 15, 2014 | Korg Ga40 Guitar Bass Tuner W Batteries

1 Answer

How do I transpose on the yamaha p 105


You are probably trying to set the new pitch on the wrong octave. Try using the C above middle C as the center point.

Jan 30, 2014 | Yamaha P95 Digital Piano

1 Answer

Just bought a ps-6 today, tried it through my overall set up the pitch shifter, detuner & super bend are fine, as soon as i use the harmony setting it takes a sweet medium gain lead sound and adds the...


By ading in the harmony signals you are combining 3 signals so gain is probably going to be high you will have to reduce it before it goes to the amp or turn down the input gain of the amp.

NEVER use a pedal in the external effects loop of an amp as the levels are wrong.

Jul 26, 2011 | Roland Boss PS-6 Harmonist Pedal

1 Answer

Pitch bender failure.


That is NOT a very descriptive problem statement... If all notes are off pitch but the bender still varies the tone, read about "transpose" in your user manual. Often the transpose or even the A440 setting gets changed and synth will be off pitch. If the pitch bender causes NO change then the control may have a failure.

May 13, 2011 | Korg Pa2X Pro Synthesizer

1 Answer

Yamaha wx5 out of tune (1 tone to low) and pitch bend wheel working up but not down...


As an electrical engineer, I suspect that one end of the resistance element or the voltage supplied to it is broken. This could be a broken circuit trace on a board or failure of the pitch wheel pot. This is iff the device has a center tapped pot. IF IT DOESN"T (schematics are hard to find on this) then the bias setting for the pitch wheel may be wrong. First thing would be to look if the the wheel has slipped on the control shaft.

Jan 03, 2011 | Yamaha WX5 Midi Wind Controller

1 Answer

I cant get my knobs or sliders on my oxygen 49 controller working keys, octave and mode and pitch work fine, its just the sliders and knobs


Here is a link that might help:http://www.m-audio.com/index.php?do=products.directlink If your DAW isn't supported it might have a learn function that might help. Make sure you download the latest update.

Oct 18, 2010 | M-Audio Oxygen 49 USB Midi Controller

1 Answer

My tyros 2 has fallen down very bad.now the left bass octave is off pitch(half note Higher) when i play the keybord with the accompaniaments.It works right ONLY when the ACMP is disambled what can i do....


Likely you have damaged the pitch bending wheel and offset it.

Try to pull it on pitch with the wheel... IF YOU CAN, then the alignment of the detent of the wheel has been disturbed and unit will need servicing... There are a lot of screws to open this and several very tender cables that can be damaged... I would recommend you take it to a shop experienced on this keyboard.

May 16, 2010 | Yamaha Full-Size Keyboard

1 Answer

When I play the sound come out distorted, like it untunes. any idea what is causing the problem? this is a for a Korg X50 and is only 2 yrs old. not korg Ma30


The manual is at:http://www.korguksupport.co.uk/upload/X50_OpGuide_E1.pdf if you don't have one. Try saving everything you want to save first if you know how to do that. Then initialize the keyboard. Follow the instructions on page 111 carefully. It sounds like you created an undesirable effect and accidently assigned the Pitch Bend Lock function to the effect. This parameter is explained on page 41 under Pitch Wheel Mod Wheel. Hope this helps.

Aug 19, 2009 | Korg Ma30

Not finding what you are looking for?
Korg X5d Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Korg Music Experts

Michial Gueffroy

Level 3 Expert

1138 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Vito Vacirca Jr.

Level 2 Expert

140 Answers

Are you a Korg Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...